Let's see everyones engine pics...

[jdm80boi]

Here's mine!

[kjlindgr]

A couple more engine and one interior shot:

[Eikon]

You better put some extra welds on the passenger seat floor pan! Danger to manifold!!!

[DJButton]

kj, looks phenomonal!

[GTR Shop]

Looks hot.. should be a nice easy 700+ at the rears in that combo.

[GTR Shop]

Pics of latest mule Pistons, Rods, Cams, turbos etc
Modified by GTR Shop at 1:04 PM 5/16/2007

[URAS]

see signature, will post some new pics soon.

[DJButton]

Yes sir some more snaps of engine would be grrreat!

[s13rb28]

GTR shop how long has that motor been pushin 603rwhp and obviously on race gas?

[GTR Shop]

GTR shop how long has that motor been pushin 603rwhp and obviously on race gas?

About 4 months.We broke the oil pump. 9200 rpm will do that Was run and tuned on 100% pump gas. 98 octane.

This is the only motor we have ever run without one of our collars as the crank was never removed from the engine... and the only one to break..

[foCk]

[minivan_don]

better ?? geting closer ??

[Booztd 3]

About 4 months.We broke the oil pump. 9200 rpm will do that Was run and tuned on 100% pump gas. 98 octane.

This is the only motor we have ever run without one of our collars as the crank was never removed from the engine... and the only one to break..

Too bad you cant get them to the guys over here stateside. I placed an order with you for one over 2 months ago, even sent the credit card number in 4 different emails as requested........never got anything and 4-5 emails later and no response. Thanks for the time though

[Yellow4g63]

POwned.

[GTR Shop]

We send out probabaly 50 or so per month.When you don't hear from someone for some time, you can only presume there is no issues.

Instead of giving us a ring, you decide to put it into a picture post.....

[Booztd 3]

Your advertisement for the collars is in every post you make, so I dont see why this is out of place.....

**Crank collars and Oil restrictors - $90us shipped for Collar + 2 Restrictors**

MattGTR ShopEmail: [email protected]://www.japaneseperformanceparts.com

[GTR Shop]

When I get back from the US, I'll scan the postage receipt and you can sort it out.. rather than you contacting me, letting me know not arrived and me sending another out at my expence...Not a mind reader......

[lazyboi444]

better ?? geting closer ??

Hey Minivan_don lol How did you clean your block up so well? Outside and Piston walls? Bored and Honed?

[minivan_don]

Hey Minivan_don lol How did you clean your block up so well? Outside and Piston walls? Bored and Honed?

.5mm over bore, honed, hot tanked and then repainted black. valve covers i just took some degreaser and scotch-brite to but the will be painted when i re-tq the head ... same as the timing belt covers.

[lazyboi444]

.5mm over bore, honed, hot tanked and then repainted black. valve covers i just took some degreaser and scotch-brite to but the will be painted when i re-tq the head ... same as the timing belt covers.

Ok so since i'm not boring. Just get the walls honed, hot tanked and then repainted black. Cuz i really don't have the money to do new pistons and rods. Did you do the repainting or the machine shop?

[Kansei240sx]

She runs... pull fans.... and the cut support are so ****ing worth it, although this picture is taken before the re-enforcements were done and everything is stiff once again...

[minivan_don]

Ok so since i'm not boring. Just get the walls honed, hot tanked and then repainted black. Cuz i really don't have the money to do new pistons and rods. Did you do the repainting or the machine shop?

machine shop did it before i even mentioned i was thinking of painting it.

[lazyboi444]

machine shop did it before i even mentioned i was thinking of painting it.

How much they charge you? For everything? Do you have yahoo messenger? if so can you im me on there. my screename is lazyboi444. i don't wanna thread jack lol. or on aim lazyboi404

[300Plus]

Ive noticed alot of people have changed the fitting on the driver side valve cover on the RB25(drive side in the US of coarse) The stock fitting has a vertical and horizontal port, I'm looking to replace mine as well but need tips on removing the stocker and what fitting to replace it with any help ? waahiven on aim or a quick answer on here

[Coolwhip]

Before it went to its 3rd tear down. Apart for improvements

[minivan_don]

How much they charge you? For everything? Do you have yahoo messenger? if so can you im me on there. my screename is lazyboi444. i don't wanna thread jack lol. or on aim lazyboi404

sorry, not on yahoo msgr.

and it costed a fair chunk of change ...

Quote »Ive noticed alot of people have changed the fitting on the driver side valve cover on the RB25(drive side in the US of coarse) The stock fitting has a vertical and horizontal port, I'm looking to replace mine as well but need tips on removing the stocker and what fitting to replace it with any help ? waahiven on aim or a quick answer on here[/quote]step 1) insert large screw driver into horizontal openingstep 2) twist and turn the fitting loose as its only pressed in (not threaded or welded)step 3) enjoy !!

[Carl H]

i just shout nasty things at those fitting till they come out, works 95.6% of the time.

[300Plus]

^^^^ Awesome thanks didn't want to break anything. Any body know the demension of the replacement fitting or a link? Thanks again guys

[cslother]

[cslother]