Need a driveshaft? Welcome SHAFTMASTERS!!!

[glitched]

When shipping the S13 or S14 shaft they typically weigh 14-15lbs. That is with the packaging included.Thanks, David

Heres hoping that packaging weighs 3- 4 pounds!

[Shaftmasters]

A new single piece aluminum driveshaft will increase torque delivered to rear axle. Because it takes less to turn the lighter shaft. It also eliminates the original 2 piece that uses a center support bearing that is bound to fail eventually.Thanks, David

[iwantans13]

A new single piece aluminum driveshaft will increase torque delivered to rear axle. Because it takes less to turn the lighter shaft. It also eliminates the original 2 piece that uses a center support bearing that is bound to fail eventually.Thanks, David

Thanks, haha.

[Florida240sx]

You coming to Nopi Nationals in ATL? I"ll swap it in the parking lot muahahaha

[Shaftmasters]

Sorry, not going to ATL. But we will ship you via UPS Ground. We will pay the shipping.Thanks, David

[nsrZ32]

Good to have you guys on board! If I need driveshafts for any of my vehicles I'll be sure to hit you up.

[Jookmasta]

i know what next i'm saving up for...............

[ralphsdiorama]

What Huh agh grrrr I just bought a driveshaft for twice the price a few weeks ago....this always happens!

[BallzDeep1.9L]

AMEN!!! half the vibration in my car is from that stupid bearing....

yeah but does it HUMMMM to at just the right RPM? mine does.. id like to blow it up

[skydragoness]

Heres hoping that packaging weighs 3- 4 pounds!

[Dano]

Dan,S14 RB25DET uses the same trans yoke & flange as the S13 RB25DET. It would simply be a matter of shaft length. You provide the measurement and we will make the shaft.Thanks, David

Modified by db240 at 9:18 AM 8/16/2007

Awesome! Very exciting, i'll see about getting you guys that length.

-Dan

[noodl35]

There any driveshafts being made for the rb26dett with rb25det transmission in a s14 (95-98 240sx)?

[Shaftmasters]

Yes. We stock the trans yoke for the rb25det trans. No problem making a shaft for you.Thanks, David

[chicos240]

ohhh man...i cant wait...too bad you guys are in MI...cause this thing is like a total impulse buy....MUst..resist...must resist

[themadscientist]

great goggleymoogley that's cheap

[ca18datsun510]

i need something slightly custom.

wanna talk here or should i email?

id call but im usually sleeping when you are working i think, im a night shift guy.

[Philsnotfalling]

I just ordered my new driveshaft. looking forward to installing it.

[ca18datsun510]

i need a custom shaft.

z32 300zx front yolk.

47 1/4" from center of u joint to center of u joint.

i will have to mail you the rear yoke, or can i just tell you the dimensions of it?

rough idea of price for this? turn around time?

[ca18datsun510]

bump for these guys. awesome customer service.

got mine the other day, quality is real nice.

ill update once i get it installed.

[ishkabibble]

If you're doing an S13 auto -> manual swap, can you just use a Shaftmasters driveshaft? Are there parts you would need from a stock S13 manual driveshaft?

[Dattebayo]

LOL SHAFTMASTERS

"we'll give you the shaft..."

(that you need )

Just joking guys

[Jookmasta]

this item is on my christmas list for sure............yall better have em in stock come december lol.

[ca18datsun510]

If you're doing an S13 auto -> manual swap, can you just use a Shaftmasters driveshaft? Are there parts you would need from a stock S13 manual driveshaft?

yes, just get the approriate manual one.

for you that would be s13 without abs.

unless you're vert has abs? i dont think it was available on them.

[Shaftmasters]

ATTENTION FORUM MEMBERS!!!Shaftmasters has trans yokes in stock again. We were out for about 3 days but not anymore. We can make you an aluminum shaft. Just click on our banner and order at your leisure.Thanks, David

[Import_Ant]

What is the rough turnaround time on these? I just placed an order for a NON-ABS S13 (89-94) driveshaft and was curious about how long I could expect it to take.

[Dano]

What is the rough turnaround time on these? I just placed an order for a NON-ABS S13 (89-94) driveshaft and was curious about how long I could expect it to take.

Thanks to me!

Aaron, I can't wait to see it, let me check out your new shaft before you install it. BAHAHAHAHAHAHA We're so immature, but it's just too easy.

[ca18datsun510]

turn around time is redonkulous.

i hung up the phone and it was sitting on my front steps.

no, really though, it was like 3 days from order or something. so fast.

here's a pic.

[kornaz]

I got a question. I have no idea about them shafts... 1. Aluminum vs. steel? I know weight is a factor, but is it as strong as steel? Other pros? I remember around 3.5 years ago my bro needed a driveshaft for his Z32, and i got it made by a machine shop (1 piece) for around $230. Sorry, i know i should've searched, but lazy right now.

[Import_Ant]

Thanks to me!

Aaron, I can't wait to see it, let me check out your new shaft before you install it. BAHAHAHAHAHAHA We're so immature, but it's just too easy.

Yes, yes thanks for the heads up. Awesome deal on these. Dan, I decided to reuse my S13 R200 pumpkin as a donor housing when I get the viscous guts. I won't have to worry about the .7~" difference with the driveshaft then (if I get a J30 unit). problem solved!

really though, it was like 3 days from order or something. so fast.

here's a pic.

That's awesome; very handsome looking shaft! Are you planning on polishing it often?
Modified by Import_Ant at 2:38 PM 9/23/2007

[Philsnotfalling]

I odered my driveshaft from shaftmasters awhile ago. However, just haven't had a chance to put my car on the lift. Finally, I installed my shaftmasters shaft tonight and I like it. I have a s13 w/o abs... the drive shaft I recievced was alittle shorter, maybe an inch, than the stock 2 piece. The only concern I have is premature wear on the rear transmission seal due to the shorter length.

Otherwise great quality, only one weight welded towards the front and perfect fitment to the differential.

Driving on it... tremndous difference. Aside from installing a nabco clutch master and slave cylinder and an ap one piece stainless line, I have a new reason to love my car. great response... it feels like more power is transfered to the ground.

I highly recommend this driveshaft due to quality and price. I would like to see a different shaft offered for abs or non-abs.