hks cast exhaust manifold fitment

Post by **matt_calgary** » Thu Dec 01, 2005 8:41 pm

Nice setup, I think cast is so much more reliable. Is that a CUSCO TYPE OS on your RB20? Do you have a greddy intake carl?? be nice to see some numbers before and after the upgrade!!!!

Post by **Yellow4g63** » Fri Dec 02, 2005 4:08 pm

matt_calgary wrote:Nice setup, I think cast is so much more reliable. Is that a CUSCO TYPE OS on your RB20? Do you have a greddy intake carl?? be nice to see some numbers before and after the upgrade!!!!

It's a rips intakemanifold like in the sig pic.

Post by **240Z_Master** » Fri Dec 02, 2005 4:35 pm

Yellow4g63 wrote:
It's a rips intakemanifold like in the sig pic.

Dude, I think he was talking about the Cusco Strut Brace in the photo.

I'm running a Cusco OS on my S30.

Post by **Yellow4g63** » Fri Dec 02, 2005 5:29 pm

240Z_Master wrote:
Dude, I think he was talking about the Cusco Strut Brace in the photo.

I'm running a Cusco OS on my S30.

He asked about a greddy intake so I thought he ment Intake manifold

matt_calgary wrote: Do you have a greddy intake carl?? be nice to see some numbers before and after the upgrade!!!!

Post by **240Z_Master** » Fri Dec 02, 2005 5:45 pm

My bad, didn't see that part of his question, lol...

BTW isn't rips from Austrailia?

Post by **matt_calgary** » Fri Dec 02, 2005 6:48 pm

Yellow4g63 wrote:
It's a rips intakemanifold like in the sig pic.

What kind of price and R&D differences are there between Greddy and rips?? Good fitment etc? Also, where did you locate it?

Post by **Yellow4g63** » Fri Dec 02, 2005 8:43 pm

matt_calgary wrote:
What kind of price and R&D differences are there between Greddy and rips?? Good fitment etc? Also, where did you locate it?

R&D not sure. Diffrence over the greddy? HUGE! since they don't make one for the rb20 lol. It fit perfect I did the install with the motor in the car. I lost some low end tq.. abot 4lbs but my power ban changed a little to the higher side of the rev range. http://www.ripsltd.co.nz/ it's not cheap I paid $1300 shipped + export fees and paypal fee. You could save a little money and not get the bored out throttle body.

Post by **matt_calgary** » Sat Dec 03, 2005 2:24 am

Yellow4g63 wrote:
R&D not sure. Diffrence over the greddy? HUGE! since they don't make one for the rb20 lol. It fit perfect I did the install with the motor in the car. I lost some low end tq.. abot 4lbs but my power ban changed a little to the higher side of the rev range. http://www.ripsltd.co.nz/ it's not cheap I paid $1300 shipped + export fees and paypal fee. You could save a little money and not get the bored out throttle body.

1300 USD? Christ thats like 1500 CDN plus I'd need a throttle body, adapter haha wow that sucker better kick ***!! Nice other products they produce thats for sure. I wonder internally if they are much difference the Greddy's? haha just thought of this, you have intake bling buddy!

Post by **Yellow4g63** » Sat Dec 03, 2005 5:11 pm

matt_calgary wrote:
1300 USD? Christ thats like 1500 CDN plus I'd need a throttle body, adapter haha wow that sucker better kick ***!! Nice other products they produce thats for sure. I wonder internally if they are much difference the Greddy's? haha just thought of this, you have intake bling buddy!

No you get a Throttle body and TPS with the intakemanifold for that price. Greddy dosen't make a manifold for the RB20 only the RB25 and RB26.

Post by **Carl H** » Sat Dec 03, 2005 5:27 pm

the rips manifold is a fantastic piece of kit, the quality is there and the product is amazing.however it is unneccisary should you be chasing power levels lower than 450whp, i did it to clean up the engine bay, make routing the fmic easier and also increace top end efficiency.as yellow4g63 said, if you want a front facing plenum then go for the rips, yes it is pricy but it speaks for its self.oh and if you should decide to order one, make sure to tell rob what kind of motor you have (s1 or s2 rb20) as the s2 engines have a dampener on the fuel rail that s1 engines dont and can cause interference problems mounting the rail.

Post by **matt_calgary** » Sat Dec 03, 2005 8:35 pm

ahh hence th

Yellow4g63 wrote:
No you get a Throttle body and TPS with the intakemanifold for that price. Greddy dosen't make a manifold for the RB20 only the RB25 and RB26.

Ahh, hence them wanting to know your prefered TB size!! I see I see. Thanks for the information guys, I'm gonna bookmark this thread right now!

Cheers

hks cast exhaust manifold fitment

Re: (eh?)

Re: (matt_calgary)

Re: (Yellow4g63)

Re: (240Z_Master)

Re: (Yellow4g63)

Re: (matt_calgary)

Re: (Yellow4g63)

Re: (matt_calgary)

Re: (Yellow4g63)

Re: (Yellow4g63)

Nissan Forums

Infiniti Forums

Datsun Forums

Technical Forums

Classifieds / Marketplace

Nissan Motorsports

General Forums