Part Numbers / Crossover Parts between USDM and JDM CA18's

Discuss topics related to the CA18DE and CA18DET series engines.
User avatar
NeedCAforS13
Posts: 4593
Joined: Mon Jan 13, 2003 3:58 pm
Car: E21 320i
HJ75 Land Cruiser
Contact:

Post

If you are looking for parts, tell the autoparts store that you have an 88' Nissan Pulsar NX SE. It will be the correct part 99% of the time!

Please note: Nissan NA is no longer making many of the gaskets,pumps, ect, for the CA18DE that was in the Pulsar. They should all still be able to be purchased from a parts store though (Advance Auto, O'Reilly,ect)

Clevite Bearings
Clevite Main Bearings - MS-1565P

Clevite Rod Bearings - CB-1287P


ARP part numbers
The Intake manifold and Rod Bolts are available through Erics Performance Parts on eBay. He doesn't list part numbers and I can't find any. I believe he has found hardware for different applications and is just re-boxing them for the CA.
202-6001 Rod Bolts - They're listed for an L20 engine, but they fit just fine.
400-8012 Exhaust Studs
165-5402 Main Stud Kit
151-2801 Flywheel Bolts - Same as a pinto. 6 in a package (The CA needs 8, so you'll have to buy 2 packages and you'll have 4 extra)
202-4702 - UK CA18DET Head Stud Kit
202-4302 - US/JDM CA18DE(T) Head Stud Kit
Head Studs
-Tightening Procedure;Torque in THREE stages: 30 ft-lbs, then 55 ft-lbs, then 80 ft-lbs (using their moly grease).loosen and re-torque THREE MORE times!Heat cycle the studs (start and run to NOT).Let the engine cool down, thoroughly check torque on studs, and tighten as necessary
-NOTE! The head stud above the water pump will sit higher than the other studs. The hole isn't as deep due to clearance issues with the pump housing in the block. How much seems to vary from motor to motor. Because of this you need to add an extra washer to this stud so the nut will not bottom out on the stud. Simpy re-use one of the stock washers.

Part numbers for belts
Alternator belt "4pk855"
- 5040340 "Advance Auto Parts"
- 4040340 "Goodyear Gatorback"
- 340k4 "Autozone"
- 040340 "NAPA"

AC belt "4pk845"
- 5040333 "Advance Auto Parts" 4 rib / 5030333 "3 rib"
- 4040333 "Goodyear Gatorback" 4 rib / 4030333 "3 rib"
- 333k4 "Autozone" 4 rib / 333k3 "3 rib"
- 0403303 "NAPA" 4 rib / 030333 "3 rib"

*the 3 rib parts numbers are for those of you who are running the AC with a staggered belt setup.

Power Steering belt "4pk840 HICAS" / "3pk840 Non-HICAS"
- 5040330 "Advance Auto Parts" 4 rib / 5030330 "3 rib"
- 4040330 "Goodyear Gatorback" 4rib / 4030330 "3 rib"
- 330k4 "Autozone" 4 rib / 330k3 "3 rib"
- 040330 "NAPA" 4 rib / 030330 "3 rib"

*4 rib belts for Hicas and 3 rib belts for Non-Hicas

NISMO motor mounts-11210-RS520 & 11220-RS520(IDK which is left or right, but whichever is shorter goes on the exhaust side of the motor.)11320-RS541 (trans mount)

Oxygen Sensor CA18ET 200sx Bosch 13276 $47.99

Spark Plugs CA18ET 200sx NGK PFR6A-11Other Spark Plug Options:PFR6/BCPR6's for standard (gap of 1.1mm) PFR7/BCPR7's for lightly modded (gap of 0.8-10mm - see what works for you) BCR8's for high boost applications. (gap 0.6-0.8 dependant on boost level) 22401-58S16 (PFR6A11, CA18) Non resistor type NGK BCP6ES11 (11 = gap of 1.1mm)

PCV Valve CA18DE Pulsar NX Bosch PCV142 $2.99

Thermostat CA18DE Pulsar NX 491-180 $4.99Thermostat 21200-V0201 (CA18 all) 82.0 C Thermostat 21200-V0206 (CA18 all) 88.0 C

Thermo Gasket CA18DE Pulsar NX Felpro 35228 $0.89

Water Pump** CA18ET ???Part Number anyone???

Upper Rad. Hose KA24DE 240SX L-564 $7.99

Lower Rad. Hose KA24DE 240SX M-563 $7.39

Oil Filter CA18DE Pulsar NX Bosch 3400 $5.49

Oil filter 15208-H8911 Ryco Z386 or Ryco Z145A

Exhaust manifold gasket 14036-D4200 (EXA 1.8, S13 CA18) Four separate pieces

Intake manifold gasket 14035-D5710 (CA18 all) Injector rail to cylinder head

Intake manifold gasket 14035-D5711 (CA18 all) Injector rail to intake runner

Turbo inlet flange gasket 14415-75F10 (200SX) or 14415-17M00 (S13 all) The Aust 200SX one fits.

Turbo outlet flange gasket 14445-26E00 (S13 all)

Engine front oil seal 13042-42L00 (CA18 all)

Engine rear oil seal 12279-18V00 (CA18 all)

Oil pan seal front 11121-01F10 (CA18 all)

Oil pan seal rear 11121-01F15 (CA18 all)

Head gasket 11044-51E00 (CA18 all) Engine gasket kit 10101-51E25 (CA18D) Engine rebuild gasket kits Engine gasket kit 10101-56E25 (CA18DET)

Valve grind gasket kit 11042-51E25 (CA18 all)

The following have proved problematic.Water pump 21010-V5528 (CA18) until 8/90 Water pump 21010-V5529 (CA18) from 8/90"]Use a CA18ET waterpump from an S12

Radiator cap 21430-01F01

IDK if these are good #'s in the US;

Radiator hose - upper 21501-35F10 (CA18 all) Radiator hose - lower 21503-35F00 (CA18 all)

Radius rods (Tension rods) 54468-35F20 (S13 all) includes bush Genuine Nissan imports (JSVA), Remanufactured with Urethane (Cars of Saigon ).

Fuel filter 16400-F5100 (CA18 and SR20) RYCO Z202 or Z201

Crank angle sensor 23731-85M10 (CA18 all)

Coolant temp sensor 25080-89903 (S13 all)

Cam shaft timing belt 13028-51E25

Cam belt idler bearing 30BD219DWAX

Cam belt tenioner bearing. 35BD219DWAX

S13 Main Handbook (English) Nissan Publication SM9E-OS13G0 $230 tax ex.

RS13 Service Manual, Main Issue (Japanese) Nissan A008009 $143 Tax Ex

crank sprocket - 13021-D4200 - $29.26

woodruff key - 00926-51900 - $1.02

crankshaft plate (behind sprocket) - 13022-42L00 - $1.78

Turbo Manifold gaskets -> head: 14036-D4201 (x2)14036-D4202 (x2)

Camshaft SealsBCA-National (Federal-Mogul) 224052

KA24 and CA18 use the same radiators (Unlike the SR) with both ports on the USDM passenger side

Knock Sensor - Part number OEM # 22060-56S10

Starter-Can use direct drive starter from an S12 CA18ET

Feel free to add any part numbers or prices, or to correct any of the above prices/numbers. This list was created awhile ago, and some stuff might not still be valid.

Sean


User avatar
Dattebayo
Posts: 33297
Joined: Sun Aug 25, 2002 10:04 am
Car: 2004 Frontier Desert Runner
Location: NE DC

Post

NeedCAforS13 wrote:Water Pump** CA18ET ???Part Number anyone???
Bosch Part Number #96060

Nowhere
Posts: 290
Joined: Wed Aug 03, 2005 1:56 pm
Car: Suzuki x-90, samurai

Post

The current part number on the air filter is 16546-0z000


User avatar
biosehnsucht
Posts: 1839
Joined: Thu Feb 26, 2004 10:20 pm
Contact:

Post

Belt info here.
Modified by biosehnsucht at 9:15 PM 2/15/2008

User avatar
Dattebayo
Posts: 33297
Joined: Sun Aug 25, 2002 10:04 am
Car: 2004 Frontier Desert Runner
Location: NE DC

Post

A bit late, but I ordered a oil pump Nissan of North America via Midway, and the part number is:

15010-35F01

From a 1988 Pulsar CA18DE.If anyone cares, Cheers!

tattman77
Posts: 28
Joined: Wed Nov 09, 2005 12:30 am
Car: 92 240sx coupe w/ca18det swap top mount 20G and s13 silvia front end

Post

ignition coils

http://www.partsamerica.com/Pr...set=A

These are the prices from advance auto parts website

Niehoff # WA2100 $70.00Borg Warner # E710 $94.00

this one is not available online (in store only) GP Sorenson # 24-5259 $101.00

I just installed the gp sorenson coil. It is a nissan reman part, so it is the exact same housing as factory. It did not come with the boot or the part that touches the plug (looks like a big flint for a lighter). Save those parts from yours.Work great so far


Modified by tattman77 at 1:48 PM 1/25/2007

User avatar
mbmbmb23
Posts: 949
Joined: Thu Aug 19, 2004 6:39 pm

Post

FYI, according to http://www.everythingnissan.com says part number 12279-18V00(CA18de rear main seal) is replaced by part number 12279-AD205

(Front main seal) part 13042-42L00 replaced with; 13042-16V00

-m

User avatar
mbmbmb23
Posts: 949
Joined: Thu Aug 19, 2004 6:39 pm

Post

Nissan T25/28 turbo compressor outlet flange (3 hole)

14465-40P03


silvia_ca18det
Posts: 179
Joined: Fri Aug 12, 2005 6:32 am
Car: 350whp ca18det drift silvia

Post

ca18det valve seals

13207-D4201

these are the same on the CA18DE and the GA16 aswell

User avatar
float_6969
Moderator
Posts: 19853
Joined: Mon Aug 26, 2002 1:55 pm
Car: CA18DET swapped 1995 Nissan 240sx (too many mods to list)
2015 SV Leaf w/QC & Bose (daily)
Location: Topeka, Kansas
Contact:

Post

ARP Main Stud Info (CA w/main bearing cap)zerothread/256288

AWDB12wagon
Posts: 314
Joined: Sat Sep 23, 2006 6:37 am
Car: 1989 Nissan Sentra 4WD

Post

NeedCAforS13 wrote:ARP FLYWHEEL BOLTS-Same as a pinto. 6 in a package. 151-2801
Will these work on the CA as well? I notice this has SR as well as CA parts listed. I need flywheel bolts anyway, and may as well get some good ones!!

User avatar
float_6969
Moderator
Posts: 19853
Joined: Mon Aug 26, 2002 1:55 pm
Car: CA18DET swapped 1995 Nissan 240sx (too many mods to list)
2015 SV Leaf w/QC & Bose (daily)
Location: Topeka, Kansas
Contact:

Post

Yea, they work just fine for the CA. You'll have to get 2 packs though as the CA18DE(T) is an 8 bolt crank.

mazdaman
Posts: 50
Joined: Thu Jun 01, 2006 6:02 am
Car: 90 S13 CA hatch

Post

Coils... Niehoff (from Advance Auto Parts) Part # WA2100 $68.99

User avatar
johngriff
Posts: 445
Joined: Tue Jul 12, 2005 8:51 pm
Car: 240sx
Contact:

Post

IMC has the rod bearings, but no main bearings, and my dealer has a set of Mains, but fast is saying "US. ONLY". Any one want to chime in on some mains for me?

User avatar
MeanGreenS13
Posts: 3483
Joined: Sat Aug 20, 2005 12:59 pm
Car: 2011 Chevrolet Silverado 2500HD
Location: Ocala, FL
Contact:

Post

anyone got an ARP # for ROD BOLTS?

User avatar
Woods Crasher
Posts: 210
Joined: Wed Jan 10, 2007 2:35 pm

Post

Vetal wrote:http://www.everythingnissan.com just told me that Nissan does not supply anymore:

water pump((
I just ordered a S12 ca18et water pump...it's superceeded to part number 21010-50VY5. confirmed 3 in stock in my NY PDC. 11 in greenvile

User avatar
RS12Turbo
Posts: 887
Joined: Wed Aug 30, 2006 3:28 pm
Contact:

Post

Woods Crasher wrote:
I just ordered a S12 ca18et water pump...it's superceeded to part number 21010-50VY5. confirmed 3 in stock in my NY PDC. 11 in greenvile
Just get one for a '84-'86 s12 ca18et from any local auto parts store

User avatar
JNM240
Posts: 1377
Joined: Wed Jul 31, 2002 2:45 pm
Car: 90 Coupe, 90 Hatch (CA18DET)
Contact:

Post

Can anybody confirm or deny that the power steering pump is the same for S13 CA18DET as it is for 88 Nissan Pulsar NX SE CA18DET?? I need to get one (motor is quite nearly finished) and will probably look at ordering from Advance or Autozone or something similar.

User avatar
MeanGreenS13
Posts: 3483
Joined: Sat Aug 20, 2005 12:59 pm
Car: 2011 Chevrolet Silverado 2500HD
Location: Ocala, FL
Contact:

Post

http://www.greenline.jp/catalo...ke=FI

performance CA parts can be found here aswell if no one has found it. i foudn this al ong time when building my old RB20

User avatar
mbmbmb23
Posts: 949
Joined: Thu Aug 19, 2004 6:39 pm

Post

Here is a link to Garrett turbo part numbers, the site is in Spain, but if you click on the correct turbo (has CA, SR/GTiR, RB, VG applications) you can get Garrett part numbers for each individual peice of the turbo.

http://www.turbomaster.info/en...issan

User avatar
biosehnsucht
Posts: 1839
Joined: Thu Feb 26, 2004 10:20 pm
Contact:

Post

Nismo mounts L/R part #'s (above it isn't sure which is which) here

11210-RS520 is RH11220-RS520 is LH

User avatar
jdznutz
Posts: 34
Joined: Fri Nov 23, 2007 10:18 am
Car: 1989 240sx Hatch

Post

Engine gasket kit just came in today from Nissan Motorsports

A0101-56E2E

Will be getting water pump and oil pump with actual part numbers as well in the near future.

User avatar
jdznutz
Posts: 34
Joined: Fri Nov 23, 2007 10:18 am
Car: 1989 240sx Hatch

Post

mbmbmb23 wrote:FYI, according to http://www.everythingnissan.com says part number 12279-18V00(CA18de rear main seal) is replaced by part number 12279-AD205

(Front main seal) part 13042-42L00 replaced with; 13042-16V00

-m
CA18DET front main = VG30DE(TT) Cam SealCA18DET Rear Main = VG30DE(TT) Rear Main

same part numbers

User avatar
sjbsuperman1425
Posts: 2889
Joined: Tue Nov 06, 2007 2:24 pm
Car: 1989 Nissan 240sx
CA18DET
Location: Bay City, MI
Contact:

Post

anybody know if a CA18DE alternator will work on the CA18DET?

User avatar
ard
Posts: 98
Joined: Sat May 31, 2008 2:19 am
Car: 1989 200sx ca18det
Contact:

Post

MeanGreenS13 wrote:anyone got an ARP # for ROD BOLTS?
did you find the part # ?can't find anywhere

yeatheshortbus
Posts: 3
Joined: Thu Sep 11, 2008 4:04 pm
Car: s13 ca18det

Post

anyone know anything (part number) about the maf or if the usdm ca18de will work for me

User avatar
sjbsuperman1425
Posts: 2889
Joined: Tue Nov 06, 2007 2:24 pm
Car: 1989 Nissan 240sx
CA18DET
Location: Bay City, MI
Contact:

Post

ok, question, where can i get the timing belt tensioner and idlers?

User avatar
ca18detgabby
Posts: 3331
Joined: Sat Feb 10, 2007 5:31 pm
Car: 92 s13 ca18det SOLD, 03 G35
Location: lake Mary FL
Contact:

Post

should be the same as the CA18DE

User avatar
s13_ono
Posts: 38
Joined: Sat Jul 28, 2007 10:29 am

Post

Hey, Ive searched, but no luck. Is the starter the same from the pulsar as well?

User avatar
KEMP
Posts: 371
Joined: Sun Nov 02, 2008 7:23 pm
Car: 1990 240sx CA18DET

Post

i do not believe so, but i think the KA24 starter may be the same...i might be wrong..


Return to “CA18DE / CA18DET Forum”