stand alone system
-
silviagtr96
- Posts: 103
- Joined: Tue Aug 16, 2005 6:04 pm
stand alone system
if i was to put an rb25det in my 1996 240sx could i use the alone system with the stock rb25det harness or would ihave to pre wire the two harness and then install the stand alone. i will use the apex power fc with commander
Re: stand alone system (silviagtr96)
im not entirley sure what you are asking but i think this is the answer:
the standalone is based on the engine harness (most are). meaning you get a standalone for the RB25 and it plugs into the factory skyline engine harness. you still need to wire the car for the engine to make everything run tho.
the standalone is based on the engine harness (most are). meaning you get a standalone for the RB25 and it plugs into the factory skyline engine harness. you still need to wire the car for the engine to make everything run tho.
-
silviagtr96
- Posts: 103
- Joined: Tue Aug 16, 2005 6:04 pm
Re: stand alone system (Kamin)
ok but can i just use the rb25det harness or do i also need the ka24de
Kamin wrote:im not entirley sure what you are asking but i think this is the answer:
the standalone is based on the engine harness (most are). meaning you get a standalone for the RB25 and it plugs into the factory skyline engine harness. you still need to wire the car for the engine to make everything run tho.
Re: stand alone system (silviagtr96)
did the ka24de come in a skyline?....silviagtr96 wrote:ok but can i just use the rb25det harness or do i also need the ka24de
-
Yellow4g63
- Posts: 3718
- Joined: Mon Jan 20, 2003 6:07 pm
- Car: 95 Nissan RB20 240SX RB20
91 Nissan NX2000 VE power
95 Nissan 240SX Stock - Contact:
Re: stand alone system (OKRB20DET)
be nice to the noob lol. If ur going to run a PFC for a RB25 you will need the RB25 engine harness. The KA24 is not a Inline 6 with coil packs. So there for you need to wire the car up with the RB25 engine harness then plug in your PFC. Make sure it works with the Stock ECU 1st and then plug in the PFC. Ohh and search PFC it will help you out when it comes time to plug it in.
-
themadscientist
- Posts: 26254
- Joined: Tue Nov 12, 2002 3:30 pm
- Car: R32 GTR, DR30 RS Turbo, BRZ, Lunchbox, NSR50 Sportster 883 Iron
- Location: Staring down at you with disdain from the spooky mountaintop castle.
Re: stand alone system (Yellow4g63)
just get a true standlone and then you don't need the RB25 harness, the KA24 harness just need to provide power to the engine management unit, guages and body harness.
some units to look at;Accel DFIAEMHaltechSDSElectromotiveFAST
some units to look at;Accel DFIAEMHaltechSDSElectromotiveFAST
-
rbsileighty
- Posts: 1694
- Joined: Sun Feb 09, 2003 8:10 am
- Car: 92 S13 Hatch w/ RB20 & 05 Audi S4 Avant 6MT
Re: stand alone system (themadscientist)
Don't forget autronic... I think I'm going to run the SM4 after doing a few years of looking. First things first though... got to catch everything up to speed in the car first.
Has anyone converted the chassis harness to a Painless kit? I've been thinking about switching it over to clean things up. Might have to find a way to make the car have fixed seatbelts though.
Has anyone converted the chassis harness to a Painless kit? I've been thinking about switching it over to clean things up. Might have to find a way to make the car have fixed seatbelts though.