SR20DET Parts Guide

Website · Post by **gtune4** » Sat Oct 28, 2006 1:47 pm

that is awesome, thank you!

only place i could find a new one had it for 600$!

Post by **AmoebAssassin** » Sun Nov 05, 2006 11:39 am

Some things I found out along the way:

SR20DET Crank bolts are M10x1.0 and will interchange with dodge omni GLHS crankshaft bolts. The Dodge bolts are 1 thread shorter and slightly heavier, so make sure to replace the opposite bolt to the one you're missing or replacing with a dodge bolt, so as not to throw off the rotating assembly.

Transmission bolts are M12x1.0 and any autozone will have these bolts in grade 12, in incrementing length by 10mm in the back of the store, you need to ask for the length.

Post by **NCturbo75** » Fri Nov 24, 2006 6:38 pm

it's a little off the subject....but those two s13 valve covers are different shades of red.

Post by **tonis56** » Tue Dec 05, 2006 6:16 am

Is there a specific part number for the item circled in red. The small plastic piece that sits above the lower seal.

thanks in advance

tony-

Post by **generic_drifter_S13** » Thu Dec 21, 2006 6:13 am

hey bro whats up??? i got a 91 silvia with a red top in it. i think its a 93 motor. my water pump went out. now when i pulled if off it didnt have a gasket. if i can find a gasket or make one. do you think it will work. also my starter went out. would it be better for me to rebuild it or to just find a new one. its and S14 tranny but the bell housing im almost exact is an S13. im new into the silvia's so im tryin to learn everything about them.. ive had mine for about 2 months now and i fell in love with the thing... but if you can help me out that would be awesome...thanks bro

Post by **C - ROD** » Tue Jan 16, 2007 11:59 am

does the FWD SR20DE oil pump & front cover assembly work on the rear wheel drive SR20DET?

& what about the Thermostat?

Post by **C - ROD** » Tue Jan 16, 2007 3:56 pm

waterpump?

Post by **C - ROD** » Tue Jan 16, 2007 5:20 pm

thanks, & 1 last thing, the valve stem seals & valve guides

Post by **C - ROD** » Tue Jan 16, 2007 5:52 pm

thanks - i can get them cheaper through my work

Post by **C - ROD** » Wed Jan 17, 2007 12:03 pm

what about the intake & exhaust valves & valve springs?

Post by **C - ROD** » Sun Jan 21, 2007 11:30 am

SpeedRacer1 wrote:Valve springs are same as an FWD SR20DE.

but what about the valves

Post by **swiff** » Sun Jan 21, 2007 12:44 pm

whatup u guyz. my names swiff i just joined, i just whanted 2 hear other peoplez oppinion, id appreciate it. ive bassicly desided on the sr20det swap for my 1990 s13 240. butt i still in some ways debate my original idea of swapping the rb26dett. the only reasons i changed my mind wass because a mixture of the price and difficulty. i would appreciate hearing others oppinions.p.s. as a rappa and drifter it kind of became enevadable that i made music for other drifters and rasers. the music i make for us is outside of my regular music career. i dnt whant ta make money from these songs i just make them so people that do what i do can vibe with it so if you would like to hear some of my songs just lett me know ill send u some.

Post by **C - ROD** » Sun Jan 21, 2007 5:12 pm

ok this is truley my last question - how do i decide what size bearings i need to get, should i just get regular size if im not machining my crank & if i machine it a litt just get like .0010 - .0020 over sized?thanks for all the help speed Racer, i just dont want to get the wrong parts for the rebuild on my sr

Post by **Shaefer Thomas** » Fri Feb 16, 2007 10:41 am

Thank you SOOOOO much to ILikeMy240sx for these numbers. Dont break off the camshaft cap bolts in the head, but if you do... here are some numbers

Camshaft Cap Bolts-Longest (bolts that go into the oil squirters): Unknown #Middle Size (approx 2.4 inches in length, M6 thread): 13058 53J00Shortest: 13058 56E00

We dont have the numbers for the longest bolts, but for the middle and smallest ones we finally have the numbers!!!

Got the bolts in today, part numbers are GOOD!!!! Woohoo!!
Modified by Shaefer Thomas at 9:34 AM 2/20/2007

Post by **TonKpilS14** » Mon Feb 26, 2007 7:36 am

I REALLY NEED a S14 sr20 Clutch fan. if somone has one please let me know. i can't find one anywhere.

Post by **nightrunner1** » Mon Mar 05, 2007 5:05 pm

can anyone help me i need a part number for the cam bolts that have the oil squirters attached to them

Post by **Lynex** » Tue Mar 06, 2007 9:43 am

Theres no way I can swap over the alternator from a SR20DE out of a Sentra over to a redtop S13 SR20DET?

Post by **turbobrick** » Tue Mar 06, 2007 6:56 pm

Hey, what is the part number for a coolent temp sensor for the ecu, for a s14 sr?

Its not the same as the ka, is it?

Post by **TonKpilS14** » Wed Mar 07, 2007 5:13 pm

hey if anyone wants a S14 sr20det MAF (mass air flow sensor) hit me up. [email protected]

Post by **turbobrick** » Thu Mar 08, 2007 8:07 pm

SpeedRacer1 wrote:
For a 1993-early 1996 S14 SR20DET use 22630-51E00 found on many US Nissans.For a mid 1996-1998 S14 SR20DET use 22630-44B20 found on many other US Nissans.

How do I find out what year my engine is?

Post by **turbobrick** » Sat Mar 10, 2007 7:41 am

I went to the dealership and they gave my 22630-51E02, which is the same one from the ka, and said it was the same thing.

Post by **Slipstream** » Mon Mar 12, 2007 2:16 pm

Is there a way to cross reference the actual numbers on your block or head to find out what year and version of engine you have?

Post by **Slipstream** » Mon Mar 12, 2007 4:32 pm

How would I break those down? I know the head is stamped 52F. I haven't really remembered the other stampings.

Post by **boostedkouki** » Wed Mar 14, 2007 11:53 pm

Is there a usdm equivilent pcv valve for the s14 sr20det?

Post by **sr20detRcr1** » Fri Mar 16, 2007 1:59 pm

anyone have the parts # on the s13 sr powersteering belt and the bolts that attach it to the engine, or what other alternatives there are for the belt

Post by **homeslicej2** » Tue Mar 20, 2007 2:23 pm

hurddawg wrote:take your gates part number to any parts store they will get you the proper belt.

I did this at my local place and they gave me Dayco belts and they worked fine. The guy told me that part numbers for belts are standardized. So they can cross-reference them easily.

K050370 AltK040345 P/S

K 05 0370....05 indicates # of ribs, 0370 indicates length of the belt. K signifies its made my Gates.

This should answer your question rb26. It's on the first page of this thread btw.

Post by **574-240sx** » Sat Mar 24, 2007 3:57 pm

Looking at the bottom end part number on the thrust washer is that the same as the thrust bearing?

Post by **streetspirit7** » Fri Mar 30, 2007 2:45 pm

will the 87 300zx O2 sensor work for the S14 SR or just the S13?

Post by **guilty_coupe13** » Mon Apr 02, 2007 8:19 am

What will work for a throw out bearing for S14 SR20DET? I've herd 93' 240sx and 93' Sentra SE-R does anybody know for sure what will work?thanks

Post by **turbobrick** » Tue Apr 03, 2007 9:06 pm

What about spark plug wires for the s14 sr20de? Will sentra se-r wires work?Also, I'm assuming the sentra spark plugs will work because they're both the n/a sr.
Modified by turbobrick at 8:05 PM 4/4/2007

SR20DET Parts Guide

Re: (myees13)

Re: SR20DET Parts Guide (Movingviolation240)

Re: (SpeedRacer1)

Re: (SpeedRacer1)

Re: (SpeedRacer1)

SR20DET

Re: (SpeedRacer1)

Re: (hurddawg)

SR20DET Parts Guide (Movingviolation240)

Re: SR20DET Parts Guide (nightrunner1)

Re: SR20DET Parts Guide

Re: SR20DET Parts Guide (SpeedRacer1)

Re: (SpeedRacer1)

Re:

Re: (SpeedRacer1)

Re: (SpeedRacer1)

Re: (Slipstream)

Re: (hurddawg)

Re: SR20DET Parts Guide (Movingviolation240)

Re: SR20DET Parts Guide

Nissan Forums

Infiniti Forums

Datsun Forums

Technical Forums

Classifieds / Marketplace

Nissan Motorsports

General Forums