s14 SR20det problem

For the RWD SR20DET cars! Sponsored by Wiring Specialties.
c0ncept
Posts: 19
Joined: Sat Jan 17, 2004 3:19 pm

Post

I have a S14 Blacktop SR in a 95-96 S14 and I need help with the wiring. I can only find s13 into a s14 but not a s14 into a s14. I have the FSM for my car but I can't find the s14 SR wiring diagrams so I do the wiring myself. I tried but the fuel pump doesn't come on and there's no spark. the only thing that i know works is the starter. Please help =(


DriftBandit
Posts: 157
Joined: Sun Oct 19, 2003 7:54 pm
Car: this is my 3rd 240sx

Post

What s14 sr20 do you have, Zenki or kouki? I have the Zenki in my zenki s14 car, and I might Be able to help you if you have the same motor as me.

-Jon

User avatar
creophus
Posts: 1142
Joined: Mon Jan 27, 2003 10:26 am
Car: 240SX SE & 200SX
Contact:

Post

Where are you located? There are guys in Tampa that do wiring. Of course its gonna cost you if you send them the uncut wiring harness. Visit http://www.xatracing.com

c0ncept
Posts: 19
Joined: Sat Jan 17, 2004 3:19 pm

Post

I have a kouki s14 sr20det. I just need the ecu and to the dash wiring diagram and i think i'll be able to make it work. can't find a damn s14 sr20det wiring diagram =(

DriftBandit
Posts: 157
Joined: Sun Oct 19, 2003 7:54 pm
Car: this is my 3rd 240sx

Post

The kouki motor is different than the zenki, I will try to find out if the dash pinouts are the same. Try http://www.zilva.com, I think that is what it is, there are factory service manuals there. If the zenki and kouki are somewhat similar I will give you my pinouts and see if they work.

c0ncept
Posts: 19
Joined: Sat Jan 17, 2004 3:19 pm

Post

Thanks...I DL'd the s14 fsm from zilvia and it was corrupted everytime i DL'd it. I also DL'd a ecu pin out from JWT but I can't understand the japanese...i hope the zenki wiring is the same as the kouki..can you send me you're wiring setup for your dash wiring DrfitBandit?

DriftBandit
Posts: 157
Joined: Sun Oct 19, 2003 7:54 pm
Car: this is my 3rd 240sx

Post

I will try to look at my wiring tomorrow. Did you just need the dash wiring or did you need the ecu also. I actually have the s14 FSM on cd and if you want to E-mail me your address I will send you a copy.

-Jon

My E-mail is [email protected]

DriftBandit
Posts: 157
Joined: Sun Oct 19, 2003 7:54 pm
Car: this is my 3rd 240sx

Post

Here is my pinout. The numbers go from left to right. The numbers not mentioned are blank on my clip.Starting from the TOP left:5-Blu/r 7-Purple10-G/o11-g/blk16-o/blu22-r/blu23-blk/y

And the bottom starting from the left again:3-o 5-y 6-blu/y 7-blu/blk 9-y/g 10-g/w 11g 12-blk 13-g/r 15-thin brown 16-r 17-thick brown 18-light g/r 19-light green/blk 20light green 21-pink 22-blu/r 24-blk/red

Hope this helps, Get back to me and tell me if it works.Good luck

c0ncept
Posts: 19
Joined: Sat Jan 17, 2004 3:19 pm

Post

thanks...i got the fuel pump working and i think it's firing up cuz when i try to turn it over it almost catches becuz b4 all this the only thing that worked was the starter..so i'm getting there...i don't have and intercooler on and i think i'm very low on gas so i think that's why it's not on...thanks again..imma get my intercooler on and some gas =)

DriftBandit
Posts: 157
Joined: Sun Oct 19, 2003 7:54 pm
Car: this is my 3rd 240sx

Post

You have no intercooler on at all, and are you running at least 91 octane gas?? Are you using starter fluid to try to start the car?


Return to “SR20DET Forum (rear-drive)”