RB27DETT Proj Updates

[StricNyne]

with all my negative news, i felt like posting some positive news... until more bad stuff happened, but i got one of the twins mounted on my motor, but i had an issue with one of the exh manifolds.... first off the company shipped me 2 of the same manifold, and number 2 the t3 flange is FUBAR and dont clear the turbo studs, so i am currently looking for a stock set of rb26 manifolds... also the adapter plate needs minor modification, so i start to take a pic with one turbo mounted to my motor and ****ign camera dies.... ohh well tommorrow i am going to be cleaning up garage a bit i will post some more pics then my goal is within next week to have motor fully assembled with turbos mounted, clutch installed, and transmission attached and have it sitting on a dolly until mounts come so i can drop it inand be done with it !!

[Andyb2637]

RB27 Huh???

[Coolwhip]

[StricNyne]

bizore and strizoke rb25

[Stealth-Z]

I have an extra sets of stock RB26 manifolds.

[StricNyne]

send me mail and a price

[nizmo zilvia]

I got a better idea....

[Coolwhip]

I got a better idea....

Saved it

[StricNyne]

pics when i get batterys in camera

[Yellow4g63]

Saved it

LoL Nice save!

[Cameron]

Saved it

lol you like that pic coolwhip, already seen it from you in 2 threads :P

[nizmo zilvia]

pics when i get batterys in camera

*cough* *cough* c h e a p a s s *cough* *cough*

[Coolwhip]

I needed to save this one quick so I opted for the closest pic I could get my hands on while at work without opening it up on my screen, lol :P

Now where are the pics!?

[Chaos the Xile]

Carlos take your lazy *** to the store and get some battries!

[StricNyne]

[Stealth-Z]

Take another look at your exhaust manifold adapters. Here is a photo of my two RB26 heads. Notice the bolt patterns.

[nizmo zilvia]

I think thats where he might be stuck at lol. It could be a easy fix though. Cut off the flanges and reweld them on how they are suppose to be and you'll be all set.

[StricNyne]

mmm yeah, that was me being retarded i had it on backwards and i had 2 stunds installed wrong... so manifolds i think will work BUT the t3 flange bolt pattern is a tad off so i need to modify that

[300Plus]

It almost looks like the adapter needs to be flipped around

[lilskyline240]

where did you get that adapter plate?

[StricNyne]

RIPS in NZ

[StricNyne]

well manifolds work, so i am gunna need longer studs, and some minor work to manifolds and adapter plate and turbos will be mounted

[StricNyne]

got quite a bit done, going to have both manifolds mounted, , and all of intake side will be done in roughly a day or so, sux but imma need a z32 align ment tool for my clutch, gunna install nismo pivot bolt, and new Throw out bearing tommorrow, has anyone seen an install write up for a twin plate clutch, i am assuming its similar to single plate, gunna use the core motor mounts, order them up tommorrow, an dhave em in roughly 3 days, so that gives me 5 days to have motor ready to be dropped in bay then comes the nightmare of wiring the haltech, anyone know any shops on east coast perfer NJ that can tune haltech as well as fab up a downpipe ? i got my gauge placement how i want it, and the circuit sports shift knob, and stri EGT and fuel psi gauge came today, hopefully some local yocals will stop by and do some small stuff for me so i can focus on prepping motor !! well i will have some juicy pics up in a day or so

[Coolwhip]

good to hear its coming along man

[rb25drag]

I installed an Cusco Exedy twin plate stage IV clutch on mine. Its not hard, Same as any other clutch install, Just make sure you have the alignment tool and you red loc tight those bolts.

Hope you upgrade your slave cylinder on the twin plate clutch, Its all I can do to push mine down. When driving around town I get a leg pump like none other.