RB25DET MOTOR BUILD (Filming SATURDAY) POST QUESTIONS

[DRIFTING.com]

RB25DET MOTOR BUILD (Filming SATURDAY) POST QUESTIONS

The RB25DET HEAD REBUILD DVD http://store.driftingshop.com/pheredvdr.htmlwas already released a few months ago and the rest of the motor will start going together on Saturday at RB MOTORING

Please post your questions about this build so we do our best to address them on the forum and in the video.

[Flamereka]

You should have dvd for just wiring conversions. Make your content available via download. Hell DRM it. you'd probably make more $$ since no packaging and shipping. I'd pay $10 for a download.

[DRIFTING.com]

You should have dvd for just wiring conversions. Make your content available via download. Hell DRM it. you'd probably make more $$ since no packaging and shipping. I'd pay $10 for a download.

thanks for the feedback

S13 or S14 chassis? The S13 Chassis DVD already existshttp://store.driftingshop.com/rbhawidvd.html

[Mute]

The next DVD will feature the installation of the following parts:

New Oil PanNEW N1 OIL PUMP

Crank Collar Discussion (Crank Collar from Eric's Performance Parts check his ebay store http://stores.ebay.com/Erics-Performance-Parts

New GasketsNew Studs (heads and mains)JE Pistons (WPC Treated)Rings with proper gaps (WPC Treated)K1 Rods and pins (WPC Treated)ACL Bearings (WPC Treated)Tomei Oil Orifice GalleysTomei HeadgasketHead Mating

Head Consists of (build shown on part 1):Tomei PoncamsTomei SpringsFerrea Valves and KeepersStock RetainersNGK SparkplugsSpeed-O-Motive Head Job (Only decking shown on video, not port and polish)

Also to be shown/used,KKR Turbo Upgrade KKR560 (Otomoto.com.au)Braille Carbon Fiber BatteryTomei Timing BeltSpec Twin Disk Clutch InstallDriveshaft Shop Upgraded AxlesTorco Racing Fluids (Oil, Lubricants, MPZ Treatment)

I'll fill in whatever blanks I may have left out later or during filming,

Thanks,

AliAli's Drift Garage
Modified by Mute at 12:58 AM 10/28/2008

[Flamereka]

not just the rb25det but also the rb20det and the rb26dett.

[Mute]

Just added, we will also be addressing the crank collar issue much to urgency as expressed by Josh Mitchell at RB Motoring who will be performing the engine work. The new collar will be installed by SPEED O MOTIVE and covered in our video. Personally I never had anyone properly explain it to me and after Josh got done I realized it really needed to be addressed before the entire long block was assembled. What can I say? He knows his stuff.

Peace,

[email protected]

[Cjmartz2k]

Will you guys be over boring/honing and if so, will you use a tourqe plate? Where would one get one for an RB? Thanks for doing the 25 BTW!

[GIJOE69]

so is the DVD available now?

[DRIFTING.com]

so is the DVD available now?

no but the short block was completed today and the content will be editing within 1 week

[StricNyne]

thats sounds like a good dvd

[DRIFTING.com]

thats sounds like a good dvd

thank you

the rest of the motor should be going together when we resume filming in 3 weeks


Modified by DRIFTING.com at 9:49 PM 10/26/2008

[Mute]

Speed O Motive conducted both the bore and the hone of our RB25 short block as well as the port and polish of our head. Not sure about where to obtain the torque plate, try calling Speed O and talking to Mike.

[Mute]

Speed O Motive http://www.speedomotive.com also installed our upgraded Crank Collar which was sponsored by Eric's Performance Parts http://stores.ebay.com/Erics-Performance-Parts

[DRIFTING.com]

sample screen shots

[DRIFTING.com]

the long block was completed last night



Editing ETA; 2 weeks,