razah9 how did u remove ur burger????

[PHENOMenalVinyl]

im thinkin i wanna take off the burger but i dont know how???? how did u do that....n vinal the mustache but i know that bc of grystorm

i tried to search it but nuthin came up sorry if this was poseted already

[packerjd04]

He had his grille custom made.

http://forums.altimas.org/zero...20941

[dldjros69]

Are you talking about the burger in the front or back.

You can pry the burger out with a screw driver, it pops out.

I have removed the burger in the back. I used a heat gun to warm up the glue behind the burger then used floss dipped in tide and used a sawing motion to remove it.

I used a little goo gone and wd40 to get rid of the extra glue.

[D-Roll]

It's simple man, just be delicate. I posted how somewhere in here

[GryStrm]

burger on face pops right off....u can take out with your bare plain hands..

i used a credit card and a heat gun on the back one...its on there nicely being that the adhesive tape is the the same shape as the emblem...to put back on...u should apply 3m moulding tape to the back and cut and trim it to be the same shape as the burger so is fully attached cheat back on the edge a bit so u dont see the tape when its on.u need to fill the shape with tape...if not water and dirt will seep in and be ugly...ull get those dirt lines streaming from it after a rain..or a wash..

alcohol swab the area u cant have any wax under the sticky thing or or it wont stick good...center line of the trunk to centerline of burger.(i used the fin of dark grey bumper bottom as a guide)...and my measurement was a heavy 1/2 above the trim piece over the lic plate to the bottom of said burger.

[PHENOMenalVinyl]

i already debadged but i want to debadge thhe front grille n vinal the mustaches i didnt know he had a new grille damit

or does the whole burger detach from the front grille with the honeycomb design behind it ????

[GryStrm]

AGHHHH...the freaking front burger pulls straight off without the grille!!..come here im in roslyn.....ill pull it off before u get out of the dumb car!

[racingtiger03]

lol, yeah the burger comes off easy. I had to use a screwdriver to get a good angle on it, but once i had a finger under it, it basically fell off. Behind it is not honeycomb however, its just a shape similar to the burger with 4 holes for it to pop into.

[LongBeachCoupe]

gry why are you in roslyn?

[GryStrm]

at the five corner intersection....for old northern blvd..to nothern blvd..near the viaduct...por qua?lol oh i thought you said where!...duh..out late last night!i work there during the day..im an architectural designer as well as a photog!,,,i due photog stuff at night mostly...

[PHENOMenalVinyl]

ok i know the burger cxomes off thats easy but i mean that whole burger set up the grey **** behind it to i mean i dont think itll look good unless its all off n ur just left with straight honeycomb

[GryStrm]

ahhh..the answer is no....as mentioned....the grey mount piece is molded into the grille slats...only the chrome burger comes off...

[Colton92]

ok i know the burger cxomes off thats easy but i mean that whole burger set up the grey **** behind it to i mean i dont think itll look good unless its all off n ur just left with straight honeycomb

Can I get a translation?

[PHENOMenalVinyl]

Can I get a translation?

No bc i dont need ur .2 in this bc ur not him and if u read the thread i already got my answer....thread complete....no more comments....thanks

[altcoupe23]

its .02 not 20 cents

[itsjustbusiness]

20 cents is alot of input!