my tomei 270 cams for sale

[nomore_mr2]

hey guys i finally found some cams alittle bigger then the tomei 270 which i bought. these are brand new and un-opened in the packages. i waited along *** time for these. like since december. these are a direct drop in cam. no adjustable cam gears required and tomei says they are suitble with stock valve srpings. these will be loud at idle and a lumpy idle but you can expect massive power gaines from them. they just wouldnt cut it for my application. i paid 575 shipped for them. i'll let them go for 525 shipped anywhere in the country. so if your gonna be using a big turbo or looking to extend ur redline these bad boys are for you. and for anyone wondering i know have 288 degree cams and 9.2mm lift

[boost_boy]

A 288 degree is not that common! Who makes the cam?

[nomore_mr2]

special company from japan hehe.

[boost_boy]

We got secrets in the camp, huh?????????:mad: Shame on you:)

[boost_boy]

With that much camshaft leads me to believe you're trying to run 9 seconds or less! How much lift is on the tomei shafts? My new cam specs are as follow: Intake 276* with a 0.438" lift and exhaust 268* 0.430" lift and I think this is more than enough camshaft to support my quest for a 10 second daily driver. Well good luck with your set up! My goal is 450whp out of my highly modified stock-bore engine. And 450whp pulling a 2200lb car should suffice, you think?

[nomore_mr2]

We got secrets in the camp, huh?????????:mad: Shame on you:)

hey a guys gotta have his little secrets right? toda makes a 288 cam. hey make cams all the way to 304.

i am trying to build myself a 10 sec car. i want to trap in the 135-140 range. i'm going for 550 with just motor and turbo. then i have a 150 direct port on top of that. ultimate goal is going to be plus 650 hp. i have been talking to a guy in japan with a full tune ca18det. hes teh one that told me the tomei 270 cams arent going to be enough for what i am after. i will be starting out with a t04r but evenutually i will be utilizing a t51r kai ball bearing. looking to switch to that in about july.

[boost_boy]

Big Boost= Big Bucks! Go ahead and represent and we'll hold the fort down on the poor folks end:D If you're using a true T04 then you're going to need those drugs to wake that engine up down low. Keep us informd on how the build is coming along.

Dee

[nomore_mr2]

well i only need my valve springs and then shes ready to put back together. the bottom end is already done and everything else is all lined up. oh well still need to get rid of the snow so i got a few more months.

[boost_boy]

Snow? What's that:D

[nomore_mr2]

its this **** that turns brown after 1 day. when you walk outside you fall on your ***. it comes from the sky cuz god is mad at me. want me to overnite you some?

[boost_boy]

Quote »want me to overnite you some? [/quote] If the post office don't mind delivering a wet package, go ahead! I won't accept it anyway. It's 85 degrees here today:D Would you like a can of heat:pface

[nomore_mr2]

hahahah

[meggala]

sounds like a great goal hmmmmmmm waiting waiting waiting for bost then bang when do you expect full boost with the t04r I have been in an rb25 with one and it came on very late and very hardvery nice enjoy.meggala

[nomore_mr2]

i'm hoping i can get full boost by 6k. we'll see though.

[JDM_1990_S13]

send me an email, i i'll take the cams from you if no one else will.. i'm in louisiana now so send me an email and we'll work soemhting out.

- Aaron

[drumma022]

Still have the Tomei Cams for sale? Will I need a solid lifter kit or valve springs to ensure the higher RPMs?Speaking of valve springs... anybody know where they are available here in the states?

Ray

Send me an IM at godzilla240sx or just send me back an email at [email protected].