I will find out tomorrow if a 300zx clutch works for the RB20.

Post by **PROJECTRB240SX** » Fri Sep 05, 2003 2:40 pm

I got my clutch today but I have a few things to do tonite, so I will let everyone know if the 300zx clutch works on the RB20 tomorrow.

Post by **spec-v5150** » Fri Sep 05, 2003 2:40 pm

Cool. I have one on my watch list on ebay. Been kinda nervous. Post up whenever you find something out. I woul dappreciate it. Since I cant sell ym car, i would like to be able to drive i t...heh heh heh

Post by **PROJECTRB240SX** » Fri Sep 05, 2003 2:40 pm

The disk is exactly the same, I just need to check the pressure plate and bearings.

Post by **JCAP_Tuning** » Fri Sep 05, 2003 2:40 pm

the pressure plate and disk both fit, the bearing is not an exact fit but will work. The flywheel will not fit from 300zx, there was a post about this earlier. I have already tried it, I will post pics when I get everything together.

Post by **sileighty89** » Fri Sep 05, 2003 2:40 pm

is the clutch kit fram na 300zx or a tt 300zx?

Post by **JCAP_Tuning** » Fri Sep 05, 2003 2:40 pm

n/a z32 (300zx)

Post by **wcbjr** » Fri Sep 05, 2003 2:40 pm

And the verdict is?

Post by **PROJECTRB240SX** » Fri Sep 05, 2003 2:40 pm

It works, but the pilot bearing is a bit tight (well in my case anyway). also the the throwout arm stop from a ka transmission works, the throwout arms are the same, so is the throwout clip.

so all in all the N/A 300ZX clutch works.

Post by **PROJECTRB240SX** » Fri Sep 05, 2003 2:40 pm

I called three times so far, No answer, so I left two messages.

Post by **wcbjr** » Fri Sep 05, 2003 2:40 pm

What brand did you get? ACT? 6-puck? Where'd ya get it? Cost? Details, man, details!

Post by **PROJECTRB240SX** » Fri Sep 05, 2003 2:40 pm

EBAY: AIMCO CLUTCHES, STOCK REPLACEMENT. I'M ONLY GOING TO USE THE RACING CLUTCH ON MY RACING MOTOR.

Post by **spec-v5150** » Fri Sep 05, 2003 2:40 pm

Same as music for me. Ia m ebaying that ****. Why pay Nissan 144 or an auto store 179. Aim gettign one for 89.99 or so

Post by **wcbjr** » Fri Sep 05, 2003 2:40 pm

That's what I thought. They have a race 6-puck available that I am going to get.

Post by **WRX to RB25DET** » Fri Sep 05, 2003 2:40 pm

what is the verdict

rb20det=300zx N/A?rb25det=300zx N/A also?

Post by **Joe** » Fri Sep 05, 2003 2:40 pm

yes. 2 of the dowel guide holes on the 300zx clutch may be a smidge off (tap with hammer to seat them) on the rb20 flywheel but all of the bolt holes line up exact.

Post by **PROJECTRB240SX** » Fri Sep 05, 2003 2:40 pm

THERE WAS NOTHING OFF ON THE RB20 FLYWHEEL AT ALL. THE ONLY PROBLEM WAS THE PILOT BEARING WAS RATHER LARGE.

I will find out tomorrow if a 300zx clutch works for the RB20.

I will find out tomorrow if a 300zx clutch works for the RB20.

Nissan Forums

Infiniti Forums

Datsun Forums

Technical Forums

Classifieds / Marketplace

Nissan Motorsports

General Forums