cam installation

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

is their a webpage that tells you how to install the 91 cams in to a ka24de? or dose anyone know how too thanks

Post by **240SXedUp** » Sat Feb 14, 2004 9:26 pm

I dont think there would be. Its pretty complicated to just show someone who's never done it. Get an FSM

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

what is an FMS? im pretty sure i can do it if i had some instructions to go by

Post by **Silent Drifter** » Sat Feb 14, 2004 9:26 pm

just mark the teeth an put em in the exact same way ur cams are in now.

Post by **Unterhandler** » Sat Feb 14, 2004 9:26 pm

Quote »what is an FMS?[/quote]

FSM = Factory Service Manual..The little book that comes with the car.

Post by **240SXedUp** » Sat Feb 14, 2004 9:26 pm

You can get a Chilton 240SX book

Post by **Touchdown038** » Sat Feb 14, 2004 9:26 pm

Unterhandler wrote:FSM = Factory Service Manual..The little book that comes with the car.

FSM didn't come with the car, unless the previous owner bought one. They usually cost around $60 on eBay.

Chilton's has instructions for the cams as well, but if you can afford the FSM instead of the $20 Chiltons, get it instead, it will save you trouble in the long run.

Post by **240SXedUp** » Sat Feb 14, 2004 9:26 pm

:WerdI believe they had FSMs on the computer or something a while back but im not sure if that was legit

Post by **Touchdown038** » Sat Feb 14, 2004 9:26 pm

They sell those over eBay for like $15, but they're just copies of a CD-R that have the manual scanned into .pdf format.

The same thing as the book, but most people would rather have the book, and I'm one of them.

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

where can i get the Chilton's book at?

Post by **Touchdown038** » Sat Feb 14, 2004 9:26 pm

Schuck's, Napa, Autozone, basically any car store around you should have them.

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

ok thanks

Post by **240SXedUp** » Sat Feb 14, 2004 9:26 pm

DOnt mistake it though... its Altima/240SX 93-98 book. they both have the KA24 of course

Post by **Silent Drifter** » Sat Feb 14, 2004 9:26 pm

yea i got that book an it has like nothing on 240's it suxors

Post by **DGA** » Sat Feb 14, 2004 9:26 pm

Actually there is, and its free. Jim Wolf technology has a web page on putting cams in a KA24DE. Its really detailed, and it takes you through every step a lot better than the factory manual, and it even has pictures. What a deal.http://jimwolftechnology.com/w...S.PDF

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

al right thanks DGA i try that instead thanks alot

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

thanks guy, i finly got the balls up to put the exhasu cam into night, i was succsuful and got it in, did it without a FSM or anything, but i just used some info i found from the NET, but got it in, runns great pulls alot harder after 5000rpm now, runs smoother, and reves easer. im happy with it..

Post by **Camel** » Sat Feb 14, 2004 9:26 pm

hey midnightsliding - did you use the proper torque specs on all the bolts? Also, what cam configuration did you decide to run? 204/248, 248/232, 248/240, 240/232? please post a link to the info you found on the web.....

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

http://www.sr20development.com....htmland im running 248/248 setup

Post by **midnightsliding** » Sat Feb 14, 2004 9:26 pm

http://forums.freshalloy.com/u...36304their another link

cam installation

cam installation

Nissan Forums

Infiniti Forums

Datsun Forums

Technical Forums

Classifieds / Marketplace

Nissan Motorsports

General Forums