Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: jspec603 at 7:33 PM 1/21/2008
First off, what is the high pressure line? (for those who aren't familiar)
The high pressure power steering hose, connects your power steering pump to your PS rack, it also is the notorious weak link in the power steering system, over time the hose breaks down and leaks, resulting in the weekly PS reservoir refills. (If you've been there, it's not fun)
Well, help is on the way!
Fujii SPL is now offering you new replacement lines! These lines are stronger, will last longer and don't cost an arm and leg!
Alright the dirty details, Specs and Pictures:
The lines can be made to work with whatever engine you have including extra *90 bends less/more length etc.
Lines are rated at 5000PSI, double the rating of the other aftermarket lines! That's the running pressure, spike pressure is four times that amount!
Connect straight to your power steering rack without the need for that extra hard-line!
Pricing is as follows:
SOHC $85.00 Shipped!
Straight from the pump to the rack on the other side! Deletes the sensor like the DOHC line does, very easy install right over the front of the engine and not down over the pulley like the stock line does.
DOHC-SR-RB-X Specify when Ordering please.
$75.00 Shipped!
Deletes the sensor and extra hard line and goes straight to the rack (the sensor increases your idle when at full steering lock, not a necessary sensor and most cars with engine swaps do not use it anyway)
LS1 to S Chassis Swap Line
$100.00 Shipped!
Stainless Steel braided for KA/SR/RB
$100.00 Shipped!
PayPal is preferred so please add in an extra 3.0% on all orders when paying with PayPal. To set up different payment methods please e-mail us at sales@fujiispl.com (that is also our PayPal account address for payment)
PAYPAL ADDRESS IS sales@fujiispl.com
Pictures:
Here are some pictures of the line that goes straight to the rack, off of an RB pump! SR/KA pumps the line will bolt directly to the back of the banjo fitting on your pump not the top of the pump.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: jspec603 at 7:33 PM 1/21/2008
Be sure to pass it on if you hear of other people in need though, these are pretty inexpensive compared to most. 
| Quote, originally posted by DJButton » |
| Man, you're the 3rd person to say! Guess I was a week too late in advertising. Be sure to pass it on if you hear of other people in need though, these are pretty inexpensive compared to most. |
NEEEDDD.... nah, do i WANT it? yess... it actually helps make the car steer more responsive right?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (240_fun)
Posted by: DJButton at 7:18 PM 1/23/2008
| Quote, originally posted by 240_fun » |
NEEEDDD.... nah, do i WANT it? yess... it actually helps make the car steer more responsive right? |
Ummm if you're leaking now, having a fully filled PS system would make it steer better.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: Kido1986 at 12:46 PM 1/24/2008
Are they ready to ship when I purchase one (like within the day or next)? I need one for a stock 92 hatch. Are those prices inc. shipping? If not, how much is S/H?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (Kido1986)
Posted by: DJButton at 2:02 PM 1/24/2008
| Quote, originally posted by thefro526 » |
| how long do you think these will be around? I just replaced mine a week or so ago and i thin i may just pick one of these up to replace that because its kind acrappy but it wont be for a while. |
but seriously I only forsee adding more things that I sell, these will be here for awhile! | Quote, originally posted by ishkabibble » |
| Is the line heat resistant and can you make them for the B13 SE-R / NX? |
| Quote, originally posted by Kido1986 » |
| Are they ready to ship when I purchase one (like within the day or next)? I need one for a stock 92 hatch. Are those prices inc. shipping? If not, how much is S/H? |
| Quote, originally posted by FUNGC » |
| hey do you have any pics of the oringal like KA, SR, lines? plus the hard line pictures? cause my high pressure hose isn't leaking but my hardline to the rack is. soo i will just need that piece. also how much is shipping to ontario? |
| Quote, originally posted by 240_fun » |
| guess that the soaking wet hoses are an indication of a slight leak? lol |
| Quote, originally posted by Nacho_240 » |
| I was just searching for the thread where you mentioned you were making these ha. I need one of these, but need to get rid of some expenses first. Looks good BTW. |
| Quote, originally posted by 240_fun » |
| yehh... im just waiting for that next paycheck to come in... but as far as deleting that sensor would that make that much of a performance difference? Just the idle when turning... but it wouldnt make it stall tho right? I see that the line goes all the way to the other side of the engine bay and loops back for no apparent reason? |
No one I know even runs the sensor and between SR's RB's and stock KA's none of us have ever had an issue, so you should be all set! The hardline loops over to the other side of the rack but the high pressure line just goes straight down to the forward hardline. If you do get one without the sensor then you'll want to remove that little hardline as our new lines go straight to the rack itself right below the steering shaft, I'll have pics up tomorrow of the new line too.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: DJButton at 7:43 PM 1/29/2008
Added new pictures to the first post, check it out! This guy is great to deal with. If you need PS lines, don't hesitate to order from him.
Thanks man. As soon as I get the new line on, Ill return the old sensor.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: d3vilskid at 12:12 AM 2/2/2008
I'll send an email soon.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (d3vilskid)
Posted by: DJButton at 1:12 AM 2/2/2008
| Quote, originally posted by d3vilskid » |
| How much to ship to the hampton, va 23666 area? Mines leak pretty bad, have to refill it like every to weeks, using the lucas kinda slows it lol. So on the ka motor by deleting the sensor, would idle drop when I turn? Just like in one of the post don't want the car to stall if not ill take the one without the sensor lol. I'll send an email soon. |
$65, shipping is free for now untill I get the prices set, so lucky you! Like I've told people, I've had my car on the road since August without the sensor, and honestly never noticed it was gone, I don't even know anyone who has the sensor still, so... basically it doesn't do a whole lot anyway!
I just got the line straight to the rack installed on mine tonight and it looks and works great if I do say so myself, I'll take some better pictures of it tomorrow!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: d3vilskid at 4:57 PM 2/2/2008
| Quote, originally posted by d3vilskid » |
| No turbo for me but high comp. |
| Quote, originally posted by s13hybrid » |
| About to email you, looking forward to having ps back! |
I am in need of s13 KADE (s14 motor if that makes a difference), with the sensor delete.
Thanks.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (s13hybrid)
Posted by: DJButton at 3:06 PM 2/7/2008
| Quote, originally posted by s13hybrid » |
I am in need of s13 KADE (s14 motor if that makes a difference), with the sensor delete. Thanks. |
...if i buy this ps line, do i still need to buy the dohc lines, or does this take care of everything?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (aurora61)
Posted by: DJButton at 2:07 PM 2/12/2008
| Quote, originally posted by aurora61 » |
| when swaping in a sr20 in a sohc 240, i know u need dohc ps lines or bend the sohc lines ...if i buy this ps line, do i still need to buy the dohc lines, or does this take care of everything? |
You'll still need the DOHC lines, which are need to reverse the side on which the high pressure ties in. If you had the engine in and wanted to provide some measurements I could probably make a line fit to length that would work though.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: 240_fun at 4:01 PM 2/12/2008
| Quote, originally posted by 240_fun » |
| hmm ill check it out thanks plus... i tried looking for a thread to wire up those 180sx turn signals but i couldnt find anything they are the turn signals and the side markers right in one piece right? so you would have to just splice into the wires from the sidemarkers on the fender and run them to that bumper light housing, right? assuming that i am keeping the OEM siemarkers... |
I haven't wired up the running lights in them yet, just the turn signals for now, just gotta cut and splice the pigtails.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: s13hybrid at 6:31 PM 2/14/2008
Thanks.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (s13hybrid)
Posted by: DJButton at 7:59 PM 2/14/2008
Good luck with it, if you get it on soon I'd love some pictures, no one has actually taken pictures and given me a full review yet! | Quote, originally posted by d3vilskid » |
| Sry bout that turns out ima have to find a different time cuz my best bud just passed |
Very sorry to hear that my friend! My thoughts and prayers with his family.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: busteds13 at 8:09 PM 2/18/2008
btw your the shiznit for makin these, thanx
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (busteds13)
Posted by: DJButton at 12:10 AM 2/19/2008
| Quote, originally posted by busteds13 » |
| ok then, ive got hicas on my car, i need the front line to the pump (closest to rad) for KA will do, its the same as CA btw your the shiznit for makin these, thanx |
$65.00 shipped can have it out to you in a couple days!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: makibaka at 4:36 PM 2/19/2008
yay for new goodies for my baby!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (busteds13)
Posted by: d3vilskid at 8:06 AM 2/20/2008
http://img.photobucket.com/alb...9.jpg
http://img.photobucket.com/alb...0.jpg
im not much of a mechanic yet, but will this fix the problem im having
i have a single cam engine
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: white240sx916 at 10:50 PM 3/3/2008
| Quote, originally posted by white240sx916 » |
| hey i desperately need one of the lines you are making. how do you accept payment. and whats shipping to 95608. thanks |
| Quote, originally posted by THE-D » |
| my power steering is leaking heres some pics of where i think its leaking from http://img.photobucket.com/alb...9.jpg
i have a single cam engine |
If it's the hose that's leaking then yes, it appears it would fix it, problem is I haven't been able to get a line made for the SOHC PS system yet. <IMG NAME="icon" SRC="http://images.nicoclub.com/forums/images/smilies/frown.gif" BORDER="0">
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: THE-D at 9:04 AM 3/5/2008
any suggestions on from where to buy one from?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (THE-D)
Posted by: DJButton at 10:24 AM 3/5/2008
| Quote, originally posted by THE-D » |
| ah damn, well thanks for replying any suggestions on from where to buy one from? |
Well if you can wait a little bit I should have one done.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: THE-D at 7:19 AM 3/6/2008
| Quote, originally posted by busteds13 » |
| got the hose today, looks all sortsa sexy ill try to take piks as soon as its in the car, its too cold right meow |
Good deal man, glad you like it. Keep in mind too that none of the fitting's are torqued down yet too. (except the ones that are clamped to the hose obviously) so don't forget to tighten them all down when you install.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: DJButton at 8:52 PM 3/16/2008
Thanks for the business as always,
Hope to help out more of you in the future.
By the way, if you just put in an order or are waiting on line still I have a couple orders going out in the next couple days, so it will be to you shortly.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: d3vilskid at 1:07 PM 3/29/2008
dont mind the engine bay its dirty lol.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (d3vilskid)
Posted by: DJButton at 7:40 PM 3/30/2008
Thanks
Regards,
D.J. Button
219 New Orchard Rd.
Epsom, NH 03234
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: d3vilskid at 6:41 PM 4/2/2008
DJ
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: d3vilskid at 11:51 AM 4/6/2008
| Quote, originally posted by DJButton » |
resulting in the weekly PS reservoir refills. (If you've been there, it's not fun) |
So its time to delete the sensor and replace the OEM line with something maybe a bit better... But to be honest I've been waiting for a reason to pick one of these up to get my maint. out of the way.
So I'll paypal you $75 for the new line, seeing as I'm going to be deleting the sensor are you interested in me shipping it to you? Obviously I won't need it anymore.
btw its for a DOHC KA...
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (1unar3clipse)
Posted by: DJButton at 9:56 PM 4/7/2008
| Quote, originally posted by 1unar3clipse » |
| So I finally sprung one of those leaks: So its time to delete the sensor and replace the OEM line with something maybe a bit better... But to be honest I've been waiting for a reason to pick one of these up to get my maint. out of the way. So I'll paypal you $75 for the new line, seeing as I'm going to be deleting the sensor are you interested in me shipping it to you? Obviously I won't need it anymore. btw its for a DOHC KA... |
Got it, thanks very much, will ship the line out tomorrow!
| Quote, originally posted by d3vilskid » |
| Sry for the delay will send out sensor this monday |
| Quote, originally posted by 3down1togo » |
| Hey quick question?... I have a leak on the high pressure hose that is connected from the pinion to the power steering pump. Just to clarify is this the same LINE you selling? If so im in need of this line because driving without power steering is a pain in the ***... Thanks |
That is affirmative, no more leaks with the new line!
1unar3clipse- Line was shipped today, thanks for the business mate!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: ninety1two40 at 1:51 PM 4/11/2008
Edit: Nevermind, sending the money now.
Modified by ninety1two40 at 5:11 PM 4/11/2008
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (ninety1two40)
Posted by: DJButton at 2:57 PM 4/11/2008
| Quote, originally posted by ninety1two40 » |
| I'd like to buy a power steering line that goes to the rack and the other end setup with the extra 90 for the RB25DET. What the price? Thanks, Steve Edit: Nevermind, sending the money now.
|
Got the money, thanks for the business! Hopefully will have it done tomorrow, if not then on Monday. Either way look for it mid next week.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: 3down1togo at 4:34 PM 4/14/2008
btw, it's for an s13 SR and I'd like to keep the sensor. LMK
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (Nacho_240)
Posted by: DJButton at 11:56 AM 5/30/2008
| Quote, originally posted by Nacho_240 » |
| My stock line is leaking so much! I'm gonna need this now. Please send final price shipped to 92801 to my email acousticnacho22@yahoo.com btw, it's for an s13 SR and I'd like to keep the sensor. LMK |
Just sent you an e-mail!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: playbass311 at 8:04 AM 6/1/2008
leo@amyway.net
-Leo
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (playbass311)
Posted by: DJButton at 10:20 AM 6/1/2008
| Quote, originally posted by playbass311 » |
| Could I please have final price (paypal) shipped for line to 20171 (VA)? Thanks! leo@amyway.net -Leo |
| Quote, originally posted by ca240sxcoupe » |
| will this line work on a ca18det pump? if so how much shipped to 30008? |
| Quote, originally posted by playbass311 » |
| Got it today! Thanks a lot man! Can't wait to put it in. |
| Quote, originally posted by wingFeather » |
| Does this replace that wierd hard line that wanders from one side under the engine & back again? I can't figure out why that things is there |
price for everything have paypal ready thx
shipped to 93257
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (outtacontrol240)
Posted by: cmoody2006 at 5:25 PM 6/10/2008
Thanks in advance
Modified by Blackspeed at 4:44 AM 6/11/2008
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (outtacontrol240)
Posted by: DJButton at 8:48 PM 6/10/2008
| Quote, originally posted by outtacontrol240 » |
| yeah im interested in a setup for my rb20 in a s13 setup........email me at skillamp @yahoo.com price for everything have paypal ready thx |
| Quote, originally posted by cmoody2006 » |
| I'll be swapping out my sohc ka for a dohc and it relocates the ps lines to the other side... Is this what I need to have in order to have ps on my new motor? |
| Quote, originally posted by Blackspeed » |
| I need one for an 04 Maxima. Can you help me out? Shoot me an email if possible kelvin.simpson@gmail.com.. Thanks in advance |
| Quote, originally posted by playbass311 » |
| Just got home from putting it in! So far so good! Install was a breeeeeze, and sooo much easier to deal with than the hardline. Great product man. |
Thanks for the great review man, very pleased I could be of service!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: cmoody2006 at 5:24 AM 6/11/2008
| Quote, originally posted by cmoody2006 » |
| Ok how much for what I need for p/s to work with my swap shipped to 47331? |
$75 shipped.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: outtacontrol240 at 11:50 AM 6/12/2008
| Quote, originally posted by outtacontrol240 » |
| payment has been sent to you dj hit me up when you get the payment |
Got it, thanks again man! Lines are getting made up tomorrow I guess, which means they'll get to shipping on Saturday. Priority so you'll see it early next week.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: Tired240 at 10:20 AM 6/19/2008
| Quote, originally posted by DJButton » |
1unar3clipse- Line was shipped today, thanks for the business mate! |
Forgot to give some feedback... but I've been too busy enjoying the feel of smooth steering 
DJbutton is the man! I might have to pick up another one in a week or so for my GF's coupe.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (Tired240)
Posted by: DJButton at 3:03 PM 6/19/2008
| Quote, originally posted by Tired240 » |
| How much for one in a ka24 in a s13 shipped to 74653? |
| Quote, originally posted by 1unar3clipse » |
Forgot to give some feedback... but I've been too busy enjoying the feel of smooth steering DJbutton is the man! I might have to pick up another one in a week or so for my GF's coupe. |
but its all good I won't drive w/o p/s 
| Quote, originally posted by cmoody2006 » |
| I'll be swapping out my sohc ka for a dohc and it relocates the ps lines to the other side... Is this what I need to have in order to have ps on my new motor? |
and i'll be doing exactly the opposite. think ya can help me?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: Tired240 at 4:00 PM 6/30/2008
i would like to purchase a high pressure power steering line to go from my rb25det pump directly to the power steering rack that is long enough and has the correct 90 and fittings , can you give me and exact price and where to send the paypal payment to thanks for your help and making these available
don
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (rb24t)
Posted by: DJButton at 7:03 PM 7/7/2008
| Quote, originally posted by rb24t » |
| djbutton i would like to purchase a high pressure power steering line to go from my rb25det pump directly to the power steering rack that is long enough and has the correct 90 and fittings , can you give me and exact price and where to send the paypal payment to thanks for your help and making these available |
the rb sits so far forward i just want to make shure its long enought?
if so i will paypal you the 75.00 bucks on wed
thanks man and thanks for making these available your a life saver.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: outtacontrol240 at 6:59 AM 7/8/2008
| Quote, originally posted by DJButton » |
| Hey Cali guys, did the lines come in yet?
|
no not yet dj ....i haven 't heard anything from the postman....i know it's no your fault but .....dam i neeeeeddddd this ahhahhah....hhahaahah
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (outtacontrol240)
Posted by: DJButton at 7:49 PM 7/8/2008
| Quote, originally posted by rb24t » |
| i dont mean to beat a dead horse but the line you supply me for 75 bucks will be long enough to go from the rack to the rb25 pump and have the correct bends and fittings? the rb sits so far forward i just want to make shure its long enought? if so i will paypal you the 75.00 bucks on wed thanks man and thanks for making these available your a life saver. |
can you send me a tracking number once it has shipped?
thanks
donovan
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (rb24t)
Posted by: DJButton at 5:54 PM 7/14/2008
For those of you who are also waiting but I haven't told you it was shipped yet that's because I'm STILL waiting on fittings, I guess the supplier of my supplier was waiting on them or something ridiculous like that. Anyhow I will post up/email you as soon as they have been shipped.
As always, thanks for the patience and most of all the business! It's always nice to hear good reviews when your're a brand new company. Now selling DMAX and Supermade products by the way, e-mail for qoutes on anything and will have a webpage up soon!
Dan Button
Fujii SPL Special Tuning Factory
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: outtacontrol240 at 4:59 AM 7/15/2008
for all the peeps out there he is really a good guy....always email me back on all the overloads email i sent him thx a lot hope i get it this time
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (outtacontrol240)
Posted by: rob808 at 4:08 PM 7/18/2008
Rob
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (rob808)
Posted by: rb24t at 3:49 PM 7/24/2008
im just curious.
rb240@centurytel.net
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (rb24t)
Posted by: rb24t at 10:44 PM 7/26/2008
i cant get a response from him on here or via email, im getting worried?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (rb24t)
Posted by: DJButton at 1:19 AM 7/27/2008
Again, terribly sorry for the wait, it was unavoidable. I believe there are three of you still waiting and I do apologize. I'm now having everything pre-made so I can just turn around and ship it when it's ordered. 10 lines in stock right now, so no worries. I'll have tracking numbers on Monday so USPS can't screw me over and lose them again.
Thanks again everyone,
DJ
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: rb24t at 1:52 PM 7/28/2008
| Quote, originally posted by rb24t » |
| did you make mine longer for the rb25-s13 ? |
| Quote, originally posted by cinek10 » |
| Payment sent this morning... |
it seems to be long enough and looks great im very pleased, thanks again for hooking me up.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (rb24t)
Posted by: DJButton at 6:15 PM 7/30/2008
| Quote, originally posted by rb24t » |
| got it today, thanks
|
Anytime man, glad you got the line hope it works out great for you! If there are any complaints let me know and I'll get is fixed!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: 89240SXCoupe at 10:41 PM 8/3/2008
if you're able to make them longer and have them ready soon, i should be able to send out a payment soon so ill keep you posted through email.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (89240SXCoupe)
Posted by: rob808 at 2:17 AM 8/4/2008
Rob
Post Title:
Posted by: cinek10 at 5:54 AM 8/4/2008
| Quote, originally posted by 89240SXCoupe » |
| Hey im in need of some lines for my rb20 swap, going from a sohc setup.. If you could lengthen them a bit for me as i believe that im going to have the same problem that rb24t did, thanks in advance. if you're able to make them longer and have them ready soon, i should be able to send out a payment soon so ill keep you posted through email. |
I can certainly do that, shoot me an e-mail at danielbutton@live.com or dan@fujiispl.com.
| Quote, originally posted by rob808 » |
| still wondering if you can make any for a SOHC KA? if so shipping quote to 96817 please? thanks! Rob |
| Quote, originally posted by cinek10 » |
| I got my line on friday! Finally got to drive my car without my home made PS line blowing off... Thanks! |
| Quote, originally posted by DJButton » |
Yo, still haven't done one for a SOHC, have a friend coming Saturday though with a SOHC and planning on measuring it out then. it will delete the sensor as the other lines do as well, and straight to the rack most likely. Oh and $75 shipped for the line. |
Great to hear Dan! Hope it works out well. Will it come with instructions too on installation? Just thought id ask since ive never had anything that needed replacing other than a radiator hose . Ill be sending in payment next week thursday.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: outtacontrol240 at 5:21 PM 8/5/2008
| Quote, originally posted by outtacontrol240 » |
| thx dj i got it at last and installed thx for the help and sry about the emails...these line are the shizznits |
Thanks man, happy it finally made it!!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: BustaGwoove at 5:40 PM 8/7/2008
| Quote, originally posted by BustaGwoove » |
| Hey man, I'm really interested in a high pressure line for a ka24de. Problem is I'm kind of on a time frame and I would need the lines asap. Can you shoot me an email at llim3@uiuc.edu with how long you think you could fabricate a line and have it shipped out to Chicago? Thanks a lot! |
Paypal is sales@fujiispl.com
Thanks,
DJ
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (DJButton)
Posted by: azsalah at 3:13 PM 8/9/2008
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (azsalah)
Posted by: DJButton at 9:41 AM 8/10/2008
| Quote, originally posted by azsalah » |
Hello, I need a hose for an '89 240sx that has the engine swaped for a KA24de . Can you make a hose that fits this setup? . If you can provide this then please let me know and I'll paypal the amout to you. Thanks. |
Sure thing man, have a couple sitting on the shelf right now! Let know if you want one!
Now offering SOHC lines too!
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (DJButton)
Posted by: rob808 at 10:48 AM 8/10/2008
| Quote, originally posted by DJButton » |
Sure thing man, have a couple sitting on the shelf right now! Let know if you want one! Now offering SOHC lines too! |
Sweet. Been waiting for this. Cant wait to send my payment in to ya Dan. Any pics of them installed?
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (DJButton)
Posted by: azsalah at 9:29 PM 8/10/2008
| Quote, originally posted by DJButton » |
Sure thing man, have a couple sitting on the shelf right now! Let know if you want one! Now offering SOHC lines too! |
Thanks a lot. I'll take one and payment has been sent.
Post Title:
Posted by: ViperSRT10 at 12:23 AM 8/13/2008
| Quote, originally posted by azsalah » |
|
Thanks for the business, line was shipped a few days ago!
| Quote, originally posted by ViperSRT10 » |
| I will be ordering lines from you in a few paychecks... Just fyi...(^_-) |
payment sent early this morning. LMK when you have it sent out. Thanks!
Rob
Post Title:
Posted by: xckid at 7:57 AM 8/14/2008
| Quote, originally posted by rob808 » |
| Hey Dan, payment sent early this morning. LMK when you have it sent out. Thanks! Rob |
Thanks, line will be sent soon as I get the ends crimped on it, which wont happan untill I get back into the machine Monday, I'll shoot you an e-mail when I ship it though!
| Quote, originally posted by xckid » |
| i shall be ordering mine soon if i get this job ...:D expect another happy customer |
Be sure to check out http://www.fujiispl.com too, as the parts will soon be available right off of the site, the business is slowly growing! Now selling DMAX, Supermade and other things!
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (DJButton)
Posted by: rob808 at 10:18 PM 8/14/2008
| Quote, originally posted by DJButton » |
Thanks, line will be sent soon as I get the ends crimped on it, which wont happan untill I get back into the machine Monday, I'll shoot you an e-mail when I ship it though! Be sure to check out http://www.fujiispl.com too, as the parts will soon be available right off of the site, the business is slowly growing! Now selling DMAX, Supermade and other things! |
Thanks! Cant wait to get it. Seems like the leak is getting bigger so im doing more refills than necessary. Damn it, why do SOHC parts have to cost more than DOHC ones 
Also checked out your site. Any plans to sell the Dmax tail lights for the fast back? I dont see it listed anywhere thats why.
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (rob808)
Posted by: DJButton at 10:06 AM 8/15/2008
| Quote, originally posted by rob808 » |
Thanks! Cant wait to get it. Seems like the leak is getting bigger so im doing more refills than necessary. Damn it, why do SOHC parts have to cost more than DOHC ones |
Where can I get these replacement steel lines?
Steve
danielsonste@earthlink.net
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (DJButton)
Posted by: azsalah at 10:25 PM 8/17/2008
Sending you paypal tonight along with my specs. Sooner you can ship it the better. Couple days won't hurt, gotta clean the engine bay + my driveway.
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (krazydriver)
Posted by: rob808 at 7:42 PM 8/26/2008
Rob
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (rob808)
Posted by: DJButton at 10:32 PM 8/26/2008
Dan
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (DJButton)
Posted by: rob808 at 3:10 AM 8/27/2008
Glad to do business with you! The instructions you sent to me i guess were similar to the DOHC lines so i guess its clear and unclear at the same time being that it just states placement of the line itself. Hope you can get install pics up soon so i can try and follow them.
Happy that i got to help push you into fabricating these lines for SOHC engine owners like myself as im sure others will appreciate the time and effort you took into making these. Just need to ask though. Would it be necessary to put teflon tape or maybe additional o-rings to help make for an air tight seal?
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (rob808)
Posted by: krazydriver at 6:36 PM 9/5/2008
Installation sucks though. I've got the JGS manifold and downpipe and it took me awhile to figure out how i wanted to route the line to fit everything.
What i did was hook the line into the DOHC's factory 90* off the pump, but use the straight fitting, so it goes straight back towards the fire wall, then i looped the line around, ziptied it to the brake line over there, and did a twisted 180* using the elbow you'd included.
Fits like a dream now, i hope it's far enough from the turbo + manifold to not cause any problems.
Worse part was installing it onto the rack. I found the easiest way was to first put in the fitting that goes into the rack. Then tighten the 90* elbow onto the 90* end of the line(at the proper angle of course). This way you can still reach around the tie rod boot and tighten the 90*'s end onto the rack fitting.
Thanks again!
Post Title: Re: High Pressure Power Steering Hoses for gththe Masses! (krazydriver)
Posted by: DJButton at 9:07 PM 9/5/2008
I've never done one for a KA-T set-up before, I made it a little long hoping it would reach. Sorry it was such a pain to get in there, the lines are meant to be bolted to the back of the stock fitting on the top of the pump, sorry didn't mention that, I should add it to this thread I guess. | Quote, originally posted by Clain » |
| How much for one for the KADE to 64055? |
Second. what size socket do i need to loosen the bolt holding down the old line from the pump? looks like a 23 mm? feels pretty tight too so i was wondering if it would be a good idea to use some sort of penetrating lubricant. its for a SOHC s13 btw. Anyone got pics of the install? thanks for any advice!
Dan if you get a chance to read this, help please?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: zamy27 at 9:17 PM 9/26/2008
| Quote, originally posted by rob808 » |
Second. what size socket do i need to loosen the bolt holding down the old line from the pump? looks like a 23 mm? feels pretty tight too so i was wondering if it would be a good idea to use some sort of penetrating lubricant. its for a SOHC s13 btw. Anyone got pics of the install? thanks for any advice! Dan if you get a chance to read this, help please? |
Rob,
Just now saw this, sorry about that. The line connects to the factory banjo fitting on the pump and is then routed around front of the engine just above the A/C or where A/C would be and bolts directly into the rack. We did fit one onto a car first to make sure it worked and everything bolted up smoothly. I thought that bolt was a 22mm but I may be mistaken.
| Quote, originally posted by zamy27 » |
| Hello, I own a 1992 infiniti m30 and I need a high pressure power steering line. I'm new to this forum so I'm not sure how it works. If you have one one for my car I would like to purchase one. I have a paypal account. If you have the hose please let me know the total price and how to pay for it. My email address is zamy27@comcast.net. Thanks, Steve |
| Quote, originally posted by thekidzkid25 » |
| nice work |
| Quote, originally posted by gabo » |
| still got these for sale, i'd like to get one for the SR s13. |
| Quote, originally posted by Jookmasta » |
| hey, sent out my shipping info in an email but was awaiting payment info so that i can get this asap. email addy is the same as this username but at gmail. let me know if you got back my response. thanks again. |
Don't think I got an e-mail but either way, you can just send a paypal to sales@fujiispl.com
Post Title:
Posted by: Jookmasta at 11:43 PM 10/8/2008
| Quote, originally posted by Jookmasta » |
| paypal'd ya. I was in correspondence with Tom so hopefully that name rings a bell lol. Nonetheless, let me know when it ships out and if there's a tracking number, please email me that as well. thanks! |
Ahh gotcha, yeah Tom said he'd been talking with a few people. I'll shoot you the tracking as soon as it's shipped out. Thanks man!
Post Title: Re: (DJButton)
Posted by: lukem80 at 9:58 AM 10/14/2008
think you can do it?
Post Title: Re: (lukem80)
Posted by: DJButton at 10:41 AM 10/14/2008
| Quote, originally posted by lukem80 » |
| I emailed you about making one of these with a LS1 PS pump fitting? think you can do it? |
Will do my best, just e-mailed you back!
Post Title:
Posted by: Jookmasta at 2:22 AM 10/15/2008
| Quote, originally posted by Jookmasta » |
| hey man, was wondering if the hose was shipped out yet? just checking. thanks in advance. |
Yeah I sent you the tracking number for it the other day, sent it to the account you have listed on paypal?
Post Title:
Posted by: nateb at 9:19 PM 10/30/2008
| Quote, originally posted by nateb » |
| i need one for a sr shipped to 07728 paypal ready |
| Quote, originally posted by DJButton » |
Sure thing, send $75 to danielbutton@live.com and I'll ship it out ASAP. |
| Quote, originally posted by nateb » |
| Money sent |
| Quote, originally posted by DJButton » |
| Got it, thanks! I'll shoot you a tracking number, soon as its sent! |
Thanks
Post Title: Re: (DJButton)
Posted by: nateb at 8:23 PM 11/11/2008
| Quote, originally posted by DJButton » |
| I'll get you the tracking number tomorrow, you should get it in a few days. |
| Quote, originally posted by nateb » |
| thanks got the line a couple days ago.....u wouldnt by chance make a line that replaces the other power steering hardlines( the ones that run across the engine bay and make that stupid loop. if not do u know the fitting sizes? |
Totally missed your post, sorry man. That looped line is just for cooling, so it loops in front to give more fluid capacity and cooling. Best bet for that is to use OEM hardlines. Or really go overkill (on a street car at least) and replace that with an actual PS cooler. I can't remember the size off the top of my head though.
| Quote, originally posted by sisedan » |
| Can you make a line that just replaces the hard line of the high pressure hose. I just bought a new hose and I can't get the hard line off of the old hose, and I destroyed the nut trying to get it off. It would be for an s13 with a redtop sr. Thanks |
We cannot make one that just replace the soft line, sorry.
Post Title: Re: (DJButton)
Posted by: Jonnie Fraz at 8:26 PM 11/16/2008
Sending you payment via Paypal right now for DOHC line.
Thanks Buddy
Jonnie
Post Title: Re: (Jonnie Fraz)
Posted by: DJButton at 9:29 PM 11/16/2008
| Quote, originally posted by Jonnie Fraz » |
| DJ, Sending you payment via Paypal right now for DOHC line. Thanks Buddy |
Thanks man, got it!
I'll shoot you a tracking number soon as it's shipped.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: idahotuner at 12:23 AM 11/22/2008
| Quote, originally posted by idahotuner » |
| i am getting ready to put PS on my 240. i havea PS rack in it but i will need all new lines and am i nthe proces of picking up a pump. i need to look at the diagrams on alldata again. bt i will be back here to get them. |
Well if the pump falls thru I can hook you up with an SR pump as well. Let me know when you're ready.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: idahotuner at 10:21 AM 11/22/2008
so how mcuh would it run for the pump and everything.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (idahotuner)
Posted by: eazye2000 at 4:14 PM 11/24/2008
Leaving it a bit longer let me route it around, and away from all the hot stuff associated with a KA-T.
Side note- Just found out we can make these at my job. lol
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (idahotuner)
Posted by: DJButton at 12:31 AM 11/25/2008
| Quote, originally posted by idahotuner » |
| oh hey well if you have everything that would be the way to go. basically i dont have any thing for PS right now besides the DOHC rack that is i nthe car. and i think a few of the lines are broken and cut off. so i would need basically every single line for it. i hope my rack is good. i may have to pull it apart and redo the seals.
|
Ben,
Say $150 for the pump and line and bracket for the pump if you need it? You'll still need a belt for pump and the hardlines that just loop in front of the rack, they're like an external fluid cooler for the PS system, so if you just want to skip them for now I can send you the two block off plugs for them as well.
Eric, thanks for the kind words, glad it's held up to the KA-Tinsanity abuse!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: idahotuner at 10:50 PM 11/25/2008
i know i will needa belt too.
waht is your pay pal
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (idahotuner)
Posted by: DJButton at 11:00 PM 11/25/2008
one more question
are you guys keeping the stock secondary hose? any advice would be valued.
Modified by yotik at 3:13 AM 12/6/2008
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (yotik)
Posted by: DJButton at 4:53 PM 12/10/2008
Christmas special, $10 off thru end of the month! | Quote, originally posted by theaustineedshelp » |
| hello, i'm totally new to any of this. i really need the high pressure hose for my 240... its a 1991 ka24 so i need to know if i can order one from you and how i go about it. thanks |
| Quote, originally posted by nyc240sx » |
| i have a 95 240sx with a rb25det in it iam interested in getting the line let me know thanks |
Was wondering if you have any hoses available for the Murano?
This is my first time on this forum so not really familiar with the paying and ordering system. (I have used paypal in the past)
Thanks for your time and help.
Wes
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (robertswes)
Posted by: my90coupe at 7:41 PM 1/7/2009
I have a 93 S13 with an RB25DET.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (robertswes)
Posted by: DJButton at 11:44 AM 1/11/2009
| Quote, originally posted by robertswes » |
| Hey. I just found you online. I have a 06 Nissan Murano and have a leak in the high pressure power steering hose (the dealership was going to charge $455 to replace). Was wondering if you have any hoses available for the Murano? This is my first time on this forum so not really familiar with the paying and ordering system. (I have used paypal in the past) Thanks for your time and help. Wes |
| Quote, originally posted by my90coupe » |
| hey im in need of a ps line for an rb20 into a 90 ka24e sohc coupe |
| Quote, originally posted by DALAZ_68 » |
| any word on CA18DET fitment |
| Quote, originally posted by johnny butt » |
| Can you still make these? I sent an e-mail a few days ago and still no response. I have a 93 S13 with an RB25DET. |
All e-mails have been responded to, unless your's didn't go thru or something you should have a reply. But yes I am still doing them! $75 shipped total!
Thanks all for the inquiry's hope I can help!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: theslimoutkast at 8:28 PM 1/20/2009
| Quote, originally posted by theslimoutkast » |
| 91 dohc... still $75? shipped to 23452. how soon can it be shipped out? |
Yup, sure is! Should have a new batch in the next couple days, usually shipped out day of or after payment. Confirmation number sent once shipped.
Thanks!
| Quote, originally posted by s13le » |
| s13, i need a rb20 line! shipped to 30052 |
I can do that! Just let me know when you're ready!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: thekawaii at 10:26 AM 1/22/2009
this puts the 2 used dohc KA lines to shame, and i wish i had done it right the first time and just ordered this to begin with. $$ well worth it.
i am using it on an RB swap in an S13.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (thekawaii)
Posted by: DJButton at 11:58 PM 1/24/2009
| Quote, originally posted by thekawaii » |
| money sent for s13 dohc
|
Thanks, got the payment! I have all the lines in stock, but running low on fittings at the moment, waiting on an order right now. (per usual, been selling these too quickly!) heh. It will be shipped early this week, I'll send you the shipping confirmation number once it's out.
| Quote, originally posted by richg » |
| how much is a line for a sr shipped to hawaii, 96782? |
| Quote, originally posted by johnny butt » |
| got my line 1 or 2 days after payment (quick), and all i can say is DAMN. this puts the 2 used dohc KA lines to shame, and i wish i had done it right the first time and just ordered this to begin with. $$ well worth it. i am using it on an RB swap in an S13. |
Thanks for the words, really appreciate it, happy to help out other 240 people!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: mattleegee at 5:09 PM 1/30/2009
I was working on mine today and the stock KA seems to long, along with how the bolt faces the wrong way so i have a huge bend in the line to make it work..... ahhh
any pics? why did someone need longer for s13?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (mattleegee)
Posted by: danman04x at 9:33 AM 2/1/2009
I emailed you also about it.
Let me know ASAP.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (mattleegee)
Posted by: DJButton at 6:36 PM 2/3/2009
| Quote, originally posted by mattleegee » |
| Are you all up on orders? Looking to order one rb25det s13 r33 crossmember I was working on mine today and the stock KA seems to long, along with how the bolt faces the wrong way so i have a huge bend in the line to make it work..... ahhh any pics? why did someone need longer for s13? |
| Quote, originally posted by danman04x » |
| Do you still have these lines? I need one for an rb20 s13 shipped to 20855 Thanks |
| Quote, originally posted by thekawaii » |
| Tracking number is not working. I emailed you also about it. Let me know ASAP. |
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: thekawaii at 11:23 AM 2/6/2009
Please resolve any issues with sellers via email, thank you.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: mattleegee at 10:18 AM 2/8/2009
| Quote, originally posted by mattleegee » |
| oops |
Oops what?
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (thekawaii)
Posted by: thekawaii at 3:57 PM 2/9/2009
He is cool.
Thank you Dan. 
Modified by thekawaii at 5:18 PM 2/9/2009
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: Steady_One_S13 at 6:27 PM 2/13/2009
| Quote, originally posted by gian52 » |
| hey i sent you an e-mail from gianvidal@gmail am real interested |
Check your inbox! Thanks.
| Quote, originally posted by mattleegee » |
| payment sent 2/24 cant wait to hear back from you! |
All orders have been recieved and are being processed, a confirmation number will be sent as soon as the line has been shipped. Thanks for the order!
Post Title:
Posted by: dori91borofc at 6:27 PM 3/2/2009
| Quote, originally posted by dori91borofc » |
| email sent from trdpsyclone@yahoo.com |
Got it, thanks!
For those waiting on orders, STILL waiting on materials on my end, I'm very sorry, its sadly unavoidable though.
Post Title: Re: (DJButton)
Posted by: JAAS at 9:36 AM 3/17/2009
Let me know either here or username @ gmail .com
Post Title: Re: (JAAS)
Posted by: DJButton at 7:47 AM 3/19/2009
| Quote, originally posted by JAAS » |
| Stock KA DOHC, shipped to 00771?? How much please. |
| Quote, originally posted by subzero122188 » |
| emailed you from my username @ yahoo. no reply as to whether you received my order or not. thanks. o i emailed you on your other email tho that you said you check more often. |
| Quote, originally posted by Veriest1 » |
| Got any for the KADE in stock? Let me know either here or username @ gmail .com |
Awsome! Great fit with a little slack to route away from turbo
Good stuff, and worth the wait, thank you!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: nice_try at 10:00 AM 3/31/2009
Post Title:
Posted by: Cidate at 11:50 AM 3/31/2009
| Quote, originally posted by Cidate » |
| same, picking up a power steering pump tomorrow from the guy i bought the car from, i'll prob order the lines tomorrow. i didn't really read the first post but how long will shipping take and how much would it cost to 2/3 day them. if its up in the first post then ignore this question. |
| Quote, originally posted by nice_try » |
| hey bro. hearin real good things about ya. i need the pressure line for a sr20det in a s13 chassis need price and pics if ya can. shipped to 39581. drop me some mail at rebelpride3000@yahoo.com |
| Quote, originally posted by mattleegee » |
| Got mine installed the other week, i forgot to post! Awsome! Great fit with a little slack to route away from turbo |
Thanks all,
DJ
Post Title: Re: (DJButton)
Posted by: TimTurboZ at 9:49 PM 4/21/2009
| Quote, originally posted by TimTurboZ » |
| Straightforward install, great seller would recommend to anyone who needs a new PS line! Thx again....too bad I have rod knock and can't enjoy my car lol! |
That stinks! Glad the line worked out though.
Post Title: Re: (DJButton)
Posted by: se7en77 at 11:54 AM 4/30/2009
LMK when u receive payment.
Modified by se7en77 at 6:26 PM 5/1/2009
Post Title: Re: (DJButton)
Posted by: ViciousCesar! at 6:55 PM 5/1/2009
| Quote, originally posted by ViciousCesar! » |
| email sent... |
| Quote, originally posted by black240jl » |
| hey man how much to make a line and the return line for an rb in an s chassis with rhd.. so stock rb power steering lines pretty much lol, i need feed and return, let me know my email is kcalblabel07@hotmail.com |
| Quote, originally posted by poli » |
| hey i just sent payment for the ps line, can't wait to get it and install it. my email is different from this one it's kiko_jm6@verizon.net please let me know if your received payment and when you ship it. |
The item arrived yesterday. It was intalled today and so far so good.
The installed wasn't difficult but it was meeessy and pain in a**.
thanks
Post Title: Re: (DJButton)
Posted by: ViciousCesar! at 7:30 PM 5/16/2009
But i put in some OT today, so i hope to have enough leftover after i order my inner and outter tie rods. I'll email you again when i'm ready. | Quote, originally posted by sleeepy240 » |
| Payment sent through paypal. The account name i sent the payment through is samantharwong@yahoo.com |
Got it, thanks for the order! I'll shoot you a tracking number soon as it's shipped!
| Quote, originally posted by ViciousCesar! » |
| I'm still trying to get the money together. I had the swine flu, well maybe the bird flu or just the regular flu last week so my pay check was weak. But i put in some OT today, so i hope to have enough leftover after i order my inner and outter tie rods. I'll email you again when i'm ready. |
No worries mate! Just let me know when you're ready.
| Quote, originally posted by bluemax » |
| Just a quick review. The item arrived yesterday. It was intalled today and so far so good. thanks |
Glad to hear! We just installed a Vr. II line yesterday, which are stainless braided for those who like the bling, and it works great! It is a messy job for sure though, especially on the rack side.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: StukSideways_Abe at 9:40 PM 5/23/2009
| Quote, originally posted by StukSideways_Abe » |
| Sent you an email. |
Responded.
| Quote, originally posted by pearli35 » |
| Hey, Do you make High Pressure Power Steering Hoses for 2002 I35? |
Haven't yet but would love the opportunity, shoot me an e-mail at dan@fujiispl.com and I'll explain how our first time system works for building new lines.
Thanks,
Dan
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: driftiteasy0113 at 6:37 PM 5/27/2009
| Quote, originally posted by driftiteasy0113 » |
| still selling these? |
You bet!
| Quote, originally posted by ak240sx » |
| email sent |
*nevermind... payment sent
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: driftiteasy0113 at 8:06 PM 6/2/2009
| Quote, originally posted by DJButton » |
You bet!
|
| Quote, originally posted by driftiteasy0113 » |
how much for the sohc ka?? |
85
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (ViciousCesar!)
Posted by: DJButton at 9:11 PM 6/3/2009
| Quote, originally posted by ViciousCesar! » |
85 |
That is correct!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: P_856 at 10:44 PM 6/7/2009
thanks
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (ViciousCesar!)
Posted by: DJButton at 7:04 PM 6/8/2009
| Quote, originally posted by P_856 » |
| hey i just sent u an email lmk |
Got it!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: P_856 at 8:57 PM 6/8/2009
| Quote, originally posted by P_856 » |
| did u reply? i didnt get anything it was sent from phyrin at gmail.com i sent it to both ur emails im looking to ordering one asap |
Well I just replied on the other address! Sorry for delay!
| Quote, originally posted by ViciousCesar! » |
| i got my line today. thank you! |
| Quote, originally posted by s13gebala » |
| money sent for sr20 hose |
Got it, should have it out tomorrow, I'll shoot you an e-mail with the tracking number.
Post Title:
Posted by: s13gebala at 12:53 PM 7/6/2009
Email at John.e.kyle@gmail.com
Need asap.
Modified by thebab at 3:04 PM 7/6/2009
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: 199240sxCoupe at 12:50 AM 7/7/2009
Any one had a problem by removing the hardline as far as power steering fluid boiling?.
Modified by 199240sxCoupe at 1:28 AM 7/7/2009
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: exodus5547097 at 8:37 AM 7/12/2009
| Quote, originally posted by thebab » |
| Need one for a 89 S13 with the SOHC (KA24E) Email at John.e.kyle@gmail.com Need asap.
|
I think I have one on stock, but if not I can have it out to you in a few days. Paypal is dan@fujiispl.com.
| Quote, originally posted by 199240sxCoupe » |
| how much for a power steering hose for a s13 ka24de shipped to 77084? Any one had a problem by removing the hardline as far as power steering fluid boiling?.
|
Nope, this line is slightly longer then factory actually to accommodate for turbocharged motors, so its not losing much capacity or cooling. The stock "cooler" line front of the cross member stays, just the high pressure line is replaced. Total with paypal fees is $77 shipped.
| Quote, originally posted by exodus5547097 » |
| I have an s13 with rb25 and rb25 power steering pump. any lines for that? |
well worth the part!! quality is perfect
Post Title: Re: (s13gebala)
Posted by: DJButton at 5:58 PM 7/21/2009
I literally can't keep these on the shelf, hence the wait time lately. I'm waiting on fittings once again now! 
Post Title: Re: (DJButton)
Posted by: pepegurr at 8:26 PM 7/21/2009
| Quote, originally posted by pepegurr » |
| I just sent you the money for my line in my RB20 coupe, thanks man. |
Got it, line will be out shortly, still waiting on the pump side fittings! Sorry!
| Quote, originally posted by driftiteasy0113 » |
| how do i get one for a ka24e? |
I don't have any new SOHC lines in stock, but I do have a slightly used one that I can send you for $40 it's our V II. stainless steel braided line.
| Quote, originally posted by 340whps13 » |
| i have a 93 240sx with an sr20det. how much for the pressure line for the power steering? |
| Quote, originally posted by driftiteasy0113 » |
| sweet!i want that line even if its used!how do we go about this?send me and email or something? |
Just paypal the $40 to dan@fujiispl.com and I'll ship the line your way, just make sure your address is included with the payment.
Post Title:
Posted by: Arrow at 8:58 PM 8/1/2009
Just installed mine - SO damn cool. Nice work, Deej!
Post Title: Re: (AZhitman)
Posted by: MATTs14 at 8:48 AM 8/13/2009
| Quote, originally posted by Arrow » |
| Hey, I know that you mentioned that you are out of stock with the SOHC power steering lines. Any idea when you might get some more in? I am looking for a replacement for mine within a month's time or so. Thanks, and awesome work! |
| Quote, originally posted by AZhitman » |
| If you have a 240, and you DON'T have one of these lines, your car sucks. Just installed mine - SO damn cool. Nice work, Deej! |
| Quote, originally posted by MATTs14 » |
| Just letting you know that i sent out a payment for a hose in an rb25 s14. Let me know if you got it please. Thanks! |
Matt, just shot you an e-mail!
Post Title: Re: (DJButton)
Posted by: AZhitman at 10:44 PM 8/16/2009
| Quote, originally posted by DJButton » |
Thanks boss... any chance on taking some pictures and adding it to one of the 'verts articles... |
Added to my list of stuff to do.
Post Title:
Posted by: Flicktitty at 5:06 PM 8/23/2009
what's the wait time on a S13 KADE/2JZ?
Post Title: Re: (Flicktitty)
Posted by: DJButton at 5:16 PM 8/26/2009
Would love to have one of yours. Any other way to get it done?
Thanks
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (nyc240sx)
Posted by: Dipsea at 3:43 PM 8/29/2009
| Quote, originally posted by nyc240sx » |
| heres the link for the hose for your murano http://www.trademotion.com/par...gid=1 |
That link seems to be broken. Do you know if there's a new one?
Thanks
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (Dipsea)
Posted by: celbii at 4:52 PM 9/8/2009
| Quote, originally posted by boneglove » |
| Will your hoses work for my 2006 murano? I have a leak as well. |
We do not have Murano line yet, sorry!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: Jadoon at 5:13 PM 9/10/2009
In order to make an M30 line we need the factory line. We have no way of replicating the hardline section with the proper fittings, so we have to use that part of the old one. If you want to send us the factory one, we can certainly do it.
Thanks,
Dan
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: elithe240guy at 5:31 PM 9/17/2009
Never mind,
You never answered me I had one made at "Hose Power" for $40 thanks anyway.....
Modified by elithe240guy at 9:34 PM 9/24/2009
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (elithe240guy)
Posted by: 199240sxCoupe at 1:10 AM 9/21/2009
| Quote, originally posted by 199240sxCoupe » |
| I still need one can paypal u 2morrow is it 75 shipped + paypal fees? I need one for a 1992 s13 ka24de |
Yeah, $77.00 should cover it. Just paypal whenever you are ready and I'll get you a tracking number once it's shipped.
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: rockuallnite at 6:56 AM 10/2/2009
Thanks
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (rockuallnite)
Posted by: white240sx916 at 6:10 PM 10/5/2009
also, any chance of pm'ing me when you have ka24e lines in stock? thanks
Modified by stinky180 at 4:47 PM 10/6/2009
Post Title:
Posted by: StricNyne at 5:52 AM 10/7/2009
| Quote, originally posted by white240sx916 » |
| do you have any dohc ka24 lines in stock, im in need of one shipped to 95825. thanks |
Sure do! Boxed and ready to go!
| Quote, originally posted by stinky180 » |
| are you still making these with rubber hoses or stainless steel? also, any chance of pm'ing me when you have ka24e lines in stock? thanks
|
I can have a SOHC line ready in few days we do rubber or SS Rubber is 85 and SS is 100 for SOHC line.
| Quote, originally posted by StricNyne » |
| yooo DJ, i wanna score one of these bad boys for my RB finally, i just got a Kouki so swapping the RB over when i get home, but i wanna have this before, price on one shipped to 08861 |
Thanks in advance
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (numbnuts240)
Posted by: DJButton at 8:02 PM 10/19/2009
| Quote, originally posted by numbnuts240 » |
| dan, i might have you bring down a dohc line the next time you come down to mark's, if it ends up being soon that is. |
Werd, just keep me reminded when the time comes!
| Quote, originally posted by Siege » |
| I want to order a high pressure power steering line, the DOHC-SR-RB line for an S13 SR20. Can you please tell me the price +shipping and 3% for paypal total? Also what is your paypal info i will need to make an order. Thanks in advance |
The total price is $77 with shipping. Paypal address is dan@fujiispl.com
Thanks!
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: Siege at 9:43 PM 10/19/2009
Thanks in advance
Modified by Siege at 9:20 PM 10/20/2009
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (Siege)
Posted by: 93nx2000 at 2:51 PM 10/23/2009
Let me know when paypal is clear on your end i show it is clear on mine as of the 23 Oct.
Thanks in advance.
Modified by Siege at 4:33 PM 10/28/2009
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: fmendoza2929 at 3:02 PM 10/26/2009
The local Nissan dealer is quoting $297!
Will your hose work for my car? Does it include the switch? If not that is cool because we are not sure it that is the problem, but the hose is definitely leaking.
Thanks
Post Title: Re: (DJButton)
Posted by: Asican at 1:39 PM 11/3/2009
| Quote, originally posted by fmendoza2929 » |
| hey DJBUTTON wats up, I heard from a fellow nico member sil240 that you can probably help me on my mission i have a (95 Right Hand Drive nissan s14 with a RB20Det swap in it im looking to put powersteering in it but my mechanic mentioned to make sure the line is fit for a RHD s14 with an rb20det motor due to the rack and pinion changing sides from the USDM edition feel free to call me at (786)239-5878 Or e-mail me at fmendoza2929@yahoo.com the sooner the better THANX |
I'll just shoot you an e-mail it will be easier that way.
| Quote, originally posted by 6thummm » |
| I drive a 2007 Maxima SE. The car has been great and then out of the blue I noticed some red fluid on the garage floor. Bummer. My mechanic tells me it is the power steerng high pressure hose that also has a switch. The local Nissan dealer is quoting $297! Will your hose work for my car? Does it include the switch? If not that is cool because we are not sure it that is the problem, but the hose is definitely leaking. |
| Quote, originally posted by Asican » |
| DO you sell these for '06 Murano as well? |
Thanks for the questions and comments!
Dan
http://www.fujiispl.com
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: ka24eracer at 9:29 PM 11/6/2009
I dont think the hose would reach both side| Quote, originally posted by ka24eracer » |
| I would love to get one for my rb25 swapped s13 but im Right hand drive I dont think the hose would reach both side |
No problem mate, we can make these whatever length you need. We've already done one for a RHD car so it's no bother. If you can possibly measure the distance from the back of the pump to the steering rack to be sure though, that would be great. Same price as the regular line too, if you are wondering.
| Quote, originally posted by bang4dabuck » |
| I need a high pressure for a 1991 Infiniti M30. Can you help a brother out ? |
Thanks guys,
Dan
Post Title: Re: High Pressure Power Steering Hoses for the Masses! (DJButton)
Posted by: bang4dabuck at 2:17 PM 11/9/2009
< Contact Us - NICO
>
Visit G37Driver.com for Infiniti G37 Information
NICOclub's Nissan forums and Infiniti forums and all affiliated sites are the property of HDS Holdings, Inc.
They are independent publications and are not affiliated with or endorsed by Nissan Motor Company or Nissan North America.
Information © Copyright © 2000-2009 by NICOclub
All rights reserved. Material may not be copied or reprinted without written permission.
Visit 370zclub.org for Nissan 370z Information