Parting out CA

[rwdconverted]

i'm parting out my CA, almost anything and everything stock is there, i have a brand new clutch, a megan racing o2 housing, and a bosh o2 sensor, all never used. aim me if interested

[yourmomsrps13]

i need the rubber pipe/connector from the cold SMIC to the throttle body.got one?

[ICdrifting]

how much for the clutch.thanks

[rwdconverted]

for the clutch $100 shipped

[Akihisa]

Is the cylinder head for sale?

[sean8564]

how about the whole motor or block what is wrong with it i have one here with rod knock

[ICdrifting]

what kind of clutch is it?

[rwdconverted]

Akihisa: cylinder head is for sale, some parts already sold, and there is a camshaft retainer bolt that snapped on the exhaust side

sean8564: the block is for sale, nothing wrong with it, last oil change was done with mobil 1 synthetic.

ICdrifting: stock replacement for ka

[sean8564]

what are you asking for it and the wiring harness with ECU I need the whole bottom end and the head plus i need a turbo my ca was shot to hell.

[rico05]

How about the cold start air regulator? Its the little doo-hickey that is inline on the tube that runs fron the coldpipe to just behind the throttle body.

[yourmomsrps13]

i need the rubber pipe/connector from the cold SMIC to the throttle body.got one?

[rwdconverted]

sean8564: i'm asking 400 for the bottom end, the wiring harness is there, but there is no ecu or ignitor, i'm asking 200 for the head, i'll drop a hundred bucks off it if you want just the head and block. and i want 75 for the turbo, its a sr13 t25 .80 AR.

rico05: have a pic? i'm a driver not a mechanic, i want to be sure i have what you're looking for.

yourmomsrps13, yea i have it. still unclear on just exactly how much you want(entire coldpipe or just the singular piece that connects to the tb)

[float_6969]

Do you still have the rubber intake for the turbo that connects to the MAFS?

[ca18detdrift]

Have the injectors? Are they the stock injectors? if you do I will buy them from you right now =)

[rwdconverted]

float_6969: nope sorry

ca18detdrift: to my knowledge the injectors are fine, make an offer

[sean8564]

ok how much for wiring harness uncut upper and lower plus Sr turbo.

[Veen]

Still have the AC compressor? Last thing I need, let me know what you want for it. [email protected]

[rwdconverted]

veen: to my knowledge i do, i have to go check, if so $50+shipping

Sean8564: 300 shipped, its in spectaculiar condition.

[sean8564]

can you do 225 for the harness and turbo I am on a tight budget since i have to rebuild the bottom end Rod knock and all

[rwdconverted]

sorry man, thats too low, and i've got somebody who's gonna drop me 75 for the turbo right now.

[sean8564]

i can do 75 for the turbo but it the wiring harness I need better price on .Sice no ECU or ignitor chip

[rwdconverted]

sorry man, the turbo is gone, i'll let you go with $250 for the harness

[tyrannix]

i need the dipstick holder (thing bolts to the block and holds the dipstick in place with a tube)

an AC bracket with the little pulley on the bottom (with all the bolts if you can)

edit> also need the tensioner for the alternator

just let me know a price to 93517

-[email protected]


Modified by tyrannix at 5:34 PM 9/16/2005

[lifelicksballs]

i know its not actually on the ca but how about p/s reservoir and lines

[rwdconverted]

nothing from the ps is still on the vehicle

[c-rad]

How about the rear main seal retainer?

[slownslurious]

coilpacks? nice to have spares.

[Pumaking]

how much can you do for the bottom end the only thing I would need is the actual block and crank nothing else. I dont need the rods, pistons etc etc. Just bare block with crank. $350 shipped sound good?

[slownslurious]

damn thats a lot for a block and a crank!

[Pumaking]

well thats with shipping, im pretty sure it aint cheap to ship it considering it probably weighs over 100lbs.