NeedCAforS13 wrote:If you are looking for parts, tell the autoparts store that you have an 88' Nissan Pulsar NX SE. It will be the correct part 99% of the time!

Please note: Nissan NA is no longer making many of the gaskets,pumps, ect, for the CA18DE that was in the Pulsar. They should all still be able to be purchased from a parts store though (Advance Auto, O'Reilly,ect)

ARP part numbers The Intake manifold and Rod Bolts are available through Erics Performance Parts on eBay. He doesn't list part numbers and I can't find any. I believe he has found hardware for different applications and is just re-boxing them for the CA.
400-8012 Exhaust Studs
165-5402 Main Stud Kit
151-2801 Flywheel Bolts - Same as a pinto. 6 in a package (The CA needs 8, so you'll have to buy 2 packages and you'll have 4 extra)
202-4702 - UK CA18DET Head Stud Kit
202-4302 - US/JDM CA18DE(T) Head Stud Kit
Head Studs
-Tightening Procedure;Torque in THREE stages: 30 ft-lbs, then 55 ft-lbs, then 80 ft-lbs (using their moly grease).loosen and re-torque THREE MORE times!Heat cycle the studs (start and run to NOT).Let the engine cool down, thoroughly check torque on studs, and tighten as necessary
-NOTE! The head stud above the water pump will sit higher than the other studs. The hole isn't as deep due to clearance issues with the pump housing in the block. How much seems to vary from motor to motor. Because of this you need to add an extra washer to this stud so the nut will not bottom out on the stud. Simpy re-use one of the stock washers.

Part numbers for belts thanks to anumeric!zerothread/284332
Alternator belt "4pk855" - 5040340 "Advance Auto Parts" - 4040340 "Goodyear Gatorback" - 340k4 "Autozone" - 040340 "NAPA"

AC belt "4pk840" - 5040335 "Advance Auto Parts" 4 rib / 5030335 "3 rib" - 4040335 "Goodyear Gatorback" 4 rib / 4030335 "3 rib" - 335k4 "Autozone" 4 rib / 335k3 "3 rib" - 040335 "NAPA" 4 rib / 030335 "3 rib"

*the 3 rib parts numbers are for those of you who are running the AC with a staggered belt setup.

Power Steering belt "4pk845 Hicas" / "3pk845 Non-Hicas" - 5040335 "Advance Auto Parts" 4 rib / 5030335 "3 rib" - 4040335 "Goodyear Gatorback" 4rib / 4030335 "3 rib" - 335k4 "Autozone" 4 rib / 335k3 "3 rib" - 040335 "NAPA" 4 rib / 030335 "3 rib"

*4 rib belts for Hicas and 3 rib belts for Non-Hicas

NISMO motor mounts-11210-RS52011220-RS520(IDK which is left or right, but which ever is shorter goes on the exhaust side of the motor.)11320-RS541 (trans mount)

Oxygen Sensor CA18ET 200sx Bosch 13276 $47.99

Spark Plugs CA18ET 200sx NGK PFR6A-11Other Spark Plug Options:PFR6/BCPR6's for standard (gap of 1.1mm) PFR7/BCPR7's for lightly modded (gap of 0.8-10mm - see what works for you) BCR8's for high boost applications. (gap 0.6-0.8 dependant on boost level) 22401-58S16 (PFR6A11, CA18) Non resistor type NGK BCP6ES11 (11 = gap of 1.1mm)

PCV Valve CA18DE Pulsar NX Bosch PCV142 $2.99

Thermostat CA18DE Pulsar NX 491-180 $4.99Thermostat 21200-V0201 (CA18 all) 82.0 C Thermostat 21200-V0206 (CA18 all) 88.0 C

Thermo Gasket CA18DE Pulsar NX Felpro 35228 $0.89

Water Pump** CA18ET ???Part Number anyone???

Upper Rad. Hose KA24DE 240SX L-564 $7.99

Lower Rad. Hose KA24DE 240SX M-563 $7.39

Oil Filter CA18DE Pulsar NX Bosch 3400 $5.49

Oil filter 15208-H8911 Ryco Z386 or Ryco Z145A

Exhaust manifold gasket 14036-D4200 (EXA 1.8, S13 CA18) Four separate pieces

Intake manifold gasket 14035-D5710 (CA18 all) Injector rail to cylinder head

Intake manifold gasket 14035-D5711 (CA18 all) Injector rail to intake runner

Turbo inlet flange gasket 14415-75F10 (200SX) or 14415-17M00 (S13 all) The Aust 200SX one fits.

Turbo outlet flange gasket 14445-26E00 (S13 all)

Engine front oil seal 13042-42L00 (CA18 all)

Engine rear oil seal 12279-18V00 (CA18 all)

Oil pan seal front 11121-01F10 (CA18 all)

Oil pan seal rear 11121-01F15 (CA18 all)

Head gasket 11044-51E00 (CA18 all) Engine gasket kit 10101-51E25 (CA18D) Engine rebuild gasket kits Engine gasket kit 10101-56E25 (CA18DET)

Valve grind gasket kit 11042-51E25 (CA18 all)

The following have proved problematic.Water pump 21010-V5528 (CA18) until 8/90 Water pump 21010-V5529 (CA18) from 8/90"]Use a CA18ET waterpump from an S12

Radiator cap 21430-01F01

IDK if these are good #'s in the USRadiator hose - upper 21501-35F10 (CA18 all) Radiator hose - lower 21503-35F00 (CA18 all)

Radius rods (Tension rods) 54468-35F20 (S13 all) includes bush Genuine Nissan imports (JSVA), Remanufactured with Urethane (Cars of Saigon ).

Fuel filter 16400-F5100 (CA18 and SR20) RYCO Z202 or Z201

Crank angle sensor 23731-85M10 (CA18 all)

Coolant temp sensor 25080-89903 (S13 all)

Cam shaft timing belt 13028-51E25

Cam belt idler bearing 30BD219DWAX

Cam belt tenioner bearing. 35BD219DWAX

S13 Main Handbook (English) Nissan Publication SM9E-OS13G0 $230 tax ex.

RS13 Service Manual, Main Issue (Japanese) Nissan A008009 $143 Tax Ex

crank sprocket - 13021-D4200 - $29.26

woodruff key - 00926-51900 - $1.02

crankshaft plate (behind sprocket) - 13022-42L00 - $1.78

Turbo Manifold gaskets -> head: 14036-D4201 (x2)14036-D4202 (x2)

Camshaft SealsBCA-National (Federal-Mogul) 224052

KA24 and CA18 use the same radiators (Unlike the SR) with both ports on the USDM passenger side

Feel free to add any part numbers or prices, or to correct any of the above prices/numbers. This list was created awhile ago, and some stuff might not still be valid.

Sean