SR20DET Parts Guide

For the RWD SR20DET cars! Sponsored by Wiring Specialties.
User avatar
Movingviolation240
Posts: 1862
Joined: Thu Apr 25, 2002 2:26 pm
Car: Big boost and flying are 2 of the 3 things I can't turn down

Post

Exhaust Manifold Gasket '91 Sentra SE-R w/SR20DE

T25 Turbo gaskets '90-'95 300ZX TT T25 gaskets (note turbo to O2 housing gasket dose not fit on S13 T25)

O2 sensor '87 300ZX Turbo

Ignitor chip '95 Q45

Fuel Injectors '95 300ZX TT (purple plugs)

Fuel Injector Seals '95 300ZXTT kit

MAF '89-'90 SOHC 240SX

Tranny rear main seal '93 240sx

Slave cylinder '93 240sx

T.O. bearing '93 240sx

Pilot bearing '93 240sx

Clutch 89 Nissan Maxima 240mm 9-7/16" spline 24x1

Belts (PS, AC, alt) Gates K050370 Alt. K040345 PS & AC

Spark Plugs NGK BKR7ES11 or BKR6 (hoter plug)

Coil Packs '90-'95 300ZX or '95 newer Maxima

S14 SR Oil Filter '95 Sentra SE-R

S13 SR Oil Filter '91 Sentra SE-R

Fuel filter '90 300zx TT

Front and Rear main seal '91 SE-R

TPS '95 KA TPS will work with some soldering

Temp sensor S13 or S14 (depending on chassis not motor) KA24DE temp sensor

Thermostat '91 Sentra SE-R

Radiator cap '90 300zx TT (slightly more pressure for better cooling over stock cap)

Knock sensor '95 240sx

Oil pressure sender '95 240sx

The only parts you really need to get from Japan are the starter, alternator, water pump, and headgasket. Most everything else can be found locally or adapted to fit. Please add to this list if you can find or think of anything else. Also corrections are appreciated.

Paul


User avatar
Movingviolation240
Posts: 1862
Joined: Thu Apr 25, 2002 2:26 pm
Car: Big boost and flying are 2 of the 3 things I can't turn down

Post

I got this off my old standby website Nissansilvia.com out of australia, might be of some use to you guys since Nissan seems to use a lot of the same part numbers internationally.

Part type Nissan Australia part number Other source or comments Oil filter 15208-H8911 Ryco Z145A (CA18 all?) Door bump rubbers 01658-J7000 (Skyline R31) Exhaust manifold gasket 14036-D4200 (EXA 1.8, S13 CA18) Four separate pieces Intake manifold gasket 14035-D5710 (CA18 all) Injector rail to cylinder head Intake manifold gasket 14035-D5711 (CA18 all) Injector rail to intake runner Intake manifold gasket 14035-53J10 (SR20 all) Turbo inlet flange gasket 14415-75F10 (200SX) or 14415-17M00 (S13 all) The Aust 200SX one fits. Turbo outlet flange gasket 14445-26E00 (S13 all) Engine front oil seal 13042-42L00 (CA18 all) Engine rear oil seal 12279-18V00 (CA18 all) Oil pan seal front 11121-01F10 (CA18 all) Oil pan seal rear 11121-01F15 (CA18 all) Head gasket 11044-51E00 (CA18 all) Head gasket 11044-50F00 (SR20) until 9/92 Head gasket 11044-50F01 (SR20) from 9/92 till 7/93 Head gasket 11044-50F10 (SR20) from7/93 onwards Engine gasket kit 10101-51E25 (CA18D) Engine rebuild gasket kits Engine gasket kit 10101-56E25 (CA18DET) Engine gasket kit 10101-50E25 (SR20DET) Engine gasket kit 10101-51E26 (SR20D) Valve grind gasket kit 11042-51E25 (CA18 all) Valve grind gasket kit 11042-50F25 (SR20 all) Fan belt 11720-V7301 (CA18 all) L = 855mm Fan belt 11720-52F00 (SR20 all) Compressor belt 11920-V7301 (CA18 all) also suits power steering pump Compressor belt 11920-30R10 (SR20 all) also suits power steering pump Water pump 21010-V5528 (CA18) until 8/90 Water pump 21010-V5529 (CA18) from 8/90 Water pump 21010-52F00 (SR20 all) Thermostat 21200-V0201 (CA18 all) 82.0 C Thermostat 21200-V0206 (CA18 all) 88.0 C Thermostat 21200-53J00 (SR20 all) Radiator cap 21430-01F01 Radiator hose - upper 21501-35F10 (CA18 all) Radiator hose - lower 21503-35F00 (CA18 all) Radiator hose - upper 21501-52F00 (SR20 all) Radiator hose - lower 21503-52F00 (SR20 all) Bonnet bump rubbers (large) 62840-D0100 (Skyline R31) Engine coolant 10120-89904 Castrol Dash switch back lights Nissan Aust, have similar types $11.00 each **** Smith P8130, with fiddling needed or 12v lamps WT2-12 from WES Components, good fit. 65c each Radius rods (Tension rods) 54468-35F20 (S13 all) includes bush Genuine Nissan imports (JSVA), Remanufactured with Urethane (Cars of Saigon ). Wheel nut 62840-21001 (R31 Skyline) Brake pads See service info page. Bendix and others. Headlight globe Who cares Any brand. H4 60/55W 12V or H4 100/55W 12V the second one has 100Watt high beam. Rear Dampers ( shockers ) See Nissan Dealer or Nismo KONI. Part no. 80-401-081 sports kyb. Approx $315 a pair. Fuel filter 16400-F5100 (CA18 and SR20) RYCO Z202 Air Filter 16546-V0100 (same as R31 Skyline) K&N high flow reusable type P/N 33-2031-1 Spark plugs 22401-58S16 (PFR6A11, CA18) Non resistor type NGK BCP6ES11 (11 = gap of 1.1mm) Spark plugs 22401-53J16 (PRF6B, SR20DET) Crank angle sensor 23731-85M10 (CA18 all) Crank angle sensor 23731-50F01 (SR20 all) Coolant temp sensor 25080-89903 (S13 all) Oil pressure sender 25240-89920 (S13 all)

User avatar
hurddawg
Posts: 241
Joined: Tue Jul 23, 2002 7:22 pm
Car: anything with 4 wheels.

Post

sr20de's timing chain will work

User avatar
hurddawg
Posts: 241
Joined: Tue Jul 23, 2002 7:22 pm
Car: anything with 4 wheels.

Post

take your gates part number to any parts store they will get you the proper belt.

I did this at my local place and they gave me Dayco belts and they worked fine. The guy told me that part numbers for belts are standardized. So they can cross-reference them easily.

K050370 AltK040345 P/S

K 05 0370....05 indicates # of ribs, 0370 indicates length of the belt. K signifies its made my Gates.

User avatar
cnichols
Posts: 1832
Joined: Tue Aug 06, 2002 6:07 pm
Car: 96 Nissan 240SX, 99 Infiniti Q45, 93 Ford Fastiva
Location: Bowling Green, KY
Contact:

Post

Also...for those running standalones that use GM style connectors (Electromotive, etc.), a 1998 Corvette coolant temp sensor threads right into the stock sensor location and of course uses a GM style connector.

Phax
Posts: 1625
Joined: Tue Nov 12, 2002 6:24 pm
Car: Control dynamics

Post

The crankshaft main bearings and thrust washers from a 92 SR20DE will fit a 92 SR20DET.

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

Alrighty so I can use the following 91 SE-R parts in my timing chain job?

13028-00008 Timing Chain 13070-00008 Timing Chain Tensioner 13079-00001 Timing Chain Tensioner Gasket 13085-00004 Timing Chain Guide - Tension Side 13075-00004 Timing Chain Guide Tension Side Bolt 13091-00005 Timing Chain Guide - Slack Side 13094-00003 Timing Chain Guide Slack Side Bolt 13510-00002 Front Crankshaft Oil Seal 15066-00003 Front Cover O-Ring

and those badboys will work no prob in the DET eh? I got those parts and part #'s off of courtesyparts.

thanks

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

The o ring sits behind the front cover bascially under the water pump. The timing chain tension side guide for USDM spec is better than the JDM one since the USDM one is metal while the JDM is all plastic.

The intake collector gasket is different from the SR20DE. So is the turbo inlet gasket from that of the VG30DETT. You'll have to take a file to the gasket's bolt holes to make it fit.

I'll list more erratta as I encounter them with my build up.

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

The connecting rods from the DE will work in the DET.

FYI guys, the DOHC KA and the SE-R spark plugs will work in the SR20DET. checked with NGK australia for the part numbers and got PFR6B-9 for double platinum plugs and got BKR6EIX for the iridium plugs. Checked NGK USA and found the BKR6EIX-11 are DOHC KA and SR20DE plugs.

The DET uses a smaller gap, 0.036" unlike the DE that uses a 0.044" gap but according to NGK's website gapping/closing the NGK plugs is not recommended < or > 0.08" so we can tap it closer. Or you can just leave it since I was told by HT that the gaps are the same for the SE-R as the DET.

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

Blacktop O2 sensors are the same as the 95 300zx twin turbo o2 sensors. They're the fat type that phase2 has.

turboimports
Posts: 111
Joined: Thu Nov 13, 2003 5:54 am

Post

question for my redtop s13 sr20det.anyone know about the 5/6 plug on my harness for the tps? i have one like this, some say it only comes with the 50mm throttle body. wich im not sure if mine is or not. it doesnt hook up to my sr20det wiring harness, because my harness is only for 3 plugs or something. some also say that i can replace the tps with one from a 91-94 usdm sentra ser? is this right? bolt up?

thanx

-Lor

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

the SE-R's is compatable with the turbo SR's. Just make sure you've a 3 wire plug. I've not seen the 5 or 6 wire TPS for the SR's, all of them I've seen are 3.

User avatar
Hijacker
Posts: 15759
Joined: Wed Aug 13, 2003 4:57 am
Car: '92 240sx Convertible
'94 F-150
Location: Fredericksburg, VA

Post

got some new part numbers for everyone. I unfortunately threw out my 5 hole turbo to O2 housing gasket bag before I could copy the part number down.

14415-17M00 4 hole gasket Exhaust manifold to turbo

32516-V5002 Shifter retainer plate gasket

ca18det_boy
Posts: 1384
Joined: Wed Dec 24, 2003 10:47 am
Location: Homestead, FL
Contact:

Post

MY TURN!!!!!

S14 SR

Rear Main Seal Set---------------BS 40628 (felpro)Oil Pump Screen gasket---------15053-1e400Main Bolts---------------------------12293-53j00Oil pump screen--------------------15050-53j13Pilot bearing-------------------------14658 (motormite)clutch fork springs------------------30514-14600clutch master------------------------cm39754 (tru torque)Injector O-rings (where it meets the mani)-----16636-72p00Head bolt washers------------------11058-53j00rod nuts--------------------------------12112-40f00fuel rail spacers-----------------------17522-10v00Connecting rod bolts-----------------12109-60j00Clutch slave----------------------------cs37493 (tru torque)

User avatar
Hijacker
Posts: 15759
Joined: Wed Aug 13, 2003 4:57 am
Car: '92 240sx Convertible
'94 F-150
Location: Fredericksburg, VA

Post

here's another couple

22020-50F00 Ignitor Chip

14052-21R00 Exhaust Plug (for AIV inlet)

14064-7B000 Studs for O2 Sensor Housing

User avatar
s13sr20chris
Posts: 4350
Joined: Tue Jun 10, 2003 9:32 am
Car: nissans
Contact:

Post

jwt says that fwd sr20de piston rings will work on rwd sr20det's. i am goint to use them on mine.

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

Front timing chain oil jet can be used from the 91 SR20DE.

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

Rocker armspart number 13257-53J03

Rocker arm guides (little grooved shim thing on top of the valve spring retainer)part number 13218-53J00

User avatar
Hijacker
Posts: 15759
Joined: Wed Aug 13, 2003 4:57 am
Car: '92 240sx Convertible
'94 F-150
Location: Fredericksburg, VA

Post

JDM part numberCam Angle Sensor: 23731 - 50F02

Not sure if there's a US equivilant for it. The P/N for the CAS is on the cap, so this is for those of us who never received a CAS cap

cheapspeed
Posts: 37
Joined: Tue Jun 15, 2004 12:07 pm
Car: 96 se

Post

a 95 and up alternator will bolt to a s13 sr with some slight modification to the tensioner mounts

stiergott
Posts: 168
Joined: Fri Jun 18, 2004 8:16 pm
Car: 240

Post

i have a ka starter bolted to my sr. all you need to use is the ka mounting bracket. if you need more info just ask

User avatar
SoCalS14
Posts: 722
Joined: Wed Mar 03, 2004 11:47 am
Car: My car...duh
Contact:

Post

S14 SR OIL FILTER = 15208-65F00

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

S13 SR TPS can be sourced from the 97 200sx.

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

Parts numbers

Front cover o-ring 15066-4j600

tensioner gasket 13079-2j200

front crank oil seal 13510-53j10

throttle body gasket 16175-53j00

timing chain oil jet 13081-53j00

Intake manifold to head gasket 14035-53j10

Piston ring set (std bore, #1 on block and pistons) 12033-53j20

Connecting rod bearings (blk) 12111-1n501

Connecting rod bearings (brn) 12111-1n500

s13 Oil filter 15208-53j00

Nismo tranny mount 11320-rs541

Crank bearing (blue) 12207-60j04

Crank bearing (yellow) 12207-60j03

Crank bearing (green) 12207-60j02
Modified by 180fan at 3:08 PM 10/19/2004

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

ARP Main Stud kit (arp part #) - 202-5402ARP Head stud kit (arp part #) - 102-4701ARP Rod bolt kit (arp part #) - 202-6005

User avatar
SoCalS14
Posts: 722
Joined: Wed Mar 03, 2004 11:47 am
Car: My car...duh
Contact:

Post

Quick parts update:

Studs for attaching the valve cover:Part # 13508-53J00

Will work on Redtop/Blacktop/Notchtop

Broke one of mine, had to find a replacement...totally sucked...

180fan
Posts: 7954
Joined: Sat Dec 14, 2002 12:16 pm
Car: 89 fastback

Post

Throwout bearing - 30502-21000

Nismo clutch fork pivot - 30537-RS540

Intake valve oil seal - 13207-D4201Exhaust valve oil seal - 13207-2B500(These two parts are from Chris' detective work, I just found the part numbers for 'em)

User avatar
s13sr20chris
Posts: 4350
Joined: Tue Jun 10, 2003 9:32 am
Car: nissans
Contact:

Post

fwd head gasket does NOT work.

mynameisjonas
Posts: 148
Joined: Mon Jul 14, 2003 10:42 am

Post

i need the throttle cable bracket, the one above the throttle body that holds the end of the cable and that you tighten the nuts down on the cable so it doesn't move. make sense? it's for sr20det redtop. is it the same one off a regular sr20de?

User avatar
Asia989
Posts: 418
Joined: Tue May 18, 2004 4:19 pm
Car: 90 s13.4
Location: Florida
Contact:

Post

will the rocker arms off of a se-r 200sx fit a sr20det,same thing with the timing chain and guides if it has that?


Return to “SR20DET Forum (rear-drive)”