motoman399
Offline
414 posts
1998 240sxse KA24DE
eureka ca
10-10-2006
|
| « Re: drilling hole for crank angle sensor (icemhan_21) | 12:14 AM 5/2/2008 |
|
so i did the best i could cause i have a s14 bell housing laying around.
 
oh and on the s14 housing the spot for the sensor is raised up a little bit about an 1/8 inch. i can get a pic of it if needed. good luck
|
icemhan_21
Offline
113 posts
1996 240sx
hendersonville tn
9-14-2007
|
hey man i appreciate your help but could you check on the pics again? coz its not working.. and if you dont mind, could you make me a stencil like that on the pic that i posted? i could pay you for it and the shipping please let me know..
|
motoman399
Offline
414 posts
1998 240sxse KA24DE
eureka ca
10-10-2006
|
| « Re: (icemhan_21) | 1:57 PM 5/3/2008 |
|
sorry about that i deleted the pics. but they are back up now. and if you still need a stencil ill make you one. or ill try. but see if this will work and let me know if you still need that made
|
diggles240
Offline
153 posts
1996 240sx SE, 2005 Altima 2.5s
VA
2-14-2008
|
| « Re: drilling hole for crank angle sensor (icemhan_21) | 10:55 PM 5/7/2008 |
|
icemhan_21: have you drilled the hole in the bellhousing for the CAS yet? i am running into the same issue on my swap. i am concerned about the precision required for the placement of the CAS. i know the sensor is an inductive type sensor that sends a signal to the ECM which, in turn, uses said signal to determine when to fire spark and inject fuel for combustion. i am uncertain of the allowable tolerance with regard to the sensor position in relation to the flywheel surface. can somebody, anybody, help out on this? this has been bugging the sh$t out of me.thanks,
kevin
EDIT: thanks for the dimensions motoman 
|
motoman399
Offline
414 posts
1998 240sxse KA24DE
eureka ca
10-10-2006
|
| « Re: drilling hole for crank angle sensor (diggles240) | 12:28 PM 5/8/2008 |
|
i am going to make a template for icemhan_21 and i can either make one for you too or when he is done he can send it to you. so let me or him know. and your welcome
|
motoman399
Offline
414 posts
1998 240sxse KA24DE
eureka ca
10-10-2006
|
| « Re: drilling hole for crank angle sensor (motoman399) | 2:57 PM 5/8/2008 |
|
alright i finally got off my butt and made this template for you guys. it was made from a s14 bell housing adapted for the s13 bell housing. you should have no problems making your holes. so here it is...
these are alignment pins so you get that perfect fit lol 
and the washer i made into a spacer for the S13 trannys only. 
P.S. the big alignment pin is the same size as the sensor hope this works great for you guys!
|
diggles240
Offline
153 posts
1996 240sx SE, 2005 Altima 2.5s
VA
2-14-2008
|
| « Re: drilling hole for crank angle sensor (motoman399) | 9:06 PM 5/8/2008 |
|
good lookin' out. thanks again motoman. how much for a template shipped to 22801? i can wait for icemhan_21 if necessary, but would like to get this mess out of the way asap  . you can e-mail me at ldiggles@yahoo.com.thanks,
kevin
|
motoman399
Offline
414 posts
1998 240sxse KA24DE
eureka ca
10-10-2006
|
| « Re: drilling hole for crank angle sensor (diggles240) | 9:55 PM 5/8/2008 |
|
diggles240- so i can have him send it back to me when he is done or i can make you a new one. i dont really want to make a new one but i will if you want me to...
|
diggles240
Offline
153 posts
1996 240sx SE, 2005 Altima 2.5s
VA
2-14-2008
|
| « Re: drilling hole for crank angle sensor (motoman399) | 10:50 PM 5/8/2008 |
|
understood. icemhan_21, what is your time frame for being finished with the template and ship to 22801? i will pay for shipping of course.thanks,
kevin
|
icemhan_21
Offline
113 posts
1996 240sx
hendersonville tn
9-14-2007
|
this guy is the most awsome man on the internet! i only asked for a card board or a sheet of paper to make the template on but he made it using metal and he even made me a spacer for the sensor. i would give this guy a million positive reps if theres any in here!
|
motoman399
Offline
414 posts
1998 240sxse KA24DE
eureka ca
10-10-2006
|
| « Re: (icemhan_21) | 1:11 AM 5/9/2008 |
|
|
EstoMax
Offline
514 posts
95 240SX KA-t
Seattle WA
6-25-2004
|
| « Re: (motoman399) | 8:07 PM 5/9/2008 |
|
just fyi you dont really need this sensor.. my s14's isnt working and it throws a CEL but has no effect on operation. i have a 95 so maybe full OBDII's have a problem with not having it, i dont know.just an FYI - don't sweat about it too much. Marko
1995 240SX with speed(Hail) dings
|
| |
