however, if you get part-way through the install, fail/give up, we charge an extra $40 to undo your work and return it to a pre-install state.

so, pay $60ish once or end up paying $100 later...

and most every reputable shop i know will tune your eq/amp/etc so that you get maximum sound quality for your whole setup.

please take it to someone reputable.

EDIT:

where in lancaster area are you? lol, ill help you do it. just saw your location...

I kinda knew what I was doing, I mean I knew the basics I just wanted to be 100% sure. I've seen my friends and cousins do this to there cars a bunch of times.

I did it today, and I finished it. It took me forever b/c I was by myself and it was a learning experience.

It sounds great, I just need some new door and rear speakers because the ones in it have been blown

But it's been done for a few hours and i've driven the car and let it sit for some time and it seems to be functioning properly. I'm happy with it

PS: I'm inbetween Denver, and Reading (i'm about a 5 minute drive from rhs13's house)

Thanks ]]> mmaxeyjr 2008-05-11T20:06:23-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3640732#3640732 nice clean hatch bro ]]> giodachamp 2008-05-11T16:13:50-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3640713#3640713 the spoiler makes a 240 look like a mitsi-talon. my friend is storing his talon at my house and i thought about pulling it off and putting it on my '90 240sx ozzman_zig 2008-05-11T16:05:10-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3640679#3640679 honestly, if you dont know what youre doing 100%, take it to a pro. at my shop (i install this stuff for a living) we charge only $60 to do a full amp/sub install. thats ridiculously cheap for the work involved to do it properly. Circuit City and Best Buy also offer lifetime warranties on their labor as well, so if you have a problem with the install, take it back to them and they fix it if its determined to be a labor mistake, not faulty product. however, if you get part-way through the install, fail/give up, we charge an extra $40 to undo your work and return it to a pre-install state. so, pay $60ish once or end up paying $100 later... and most every reputable shop i know will tune your eq/amp/etc so that you get maximum sound quality for your whole setup.please take it to someone reputable.EDIT:where in lancaster area are you lol, ill help you do it. just saw your location... however, if you get part-way through the install, fail/give up, we charge an extra $40 to undo your work and return it to a pre-install state.

so, pay $60ish once or end up paying $100 later...

and most every reputable shop i know will tune your eq/amp/etc so that you get maximum sound quality for your whole setup.

please take it to someone reputable.

EDIT:

where in lancaster area are you? lol, ill help you do it. just saw your location... ]]> mrgreeneyes 2008-05-11T15:48:48-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3640458#3640458 alright i got it all going right now. I just need ground wires, and i need to put in my subs. I hope it works.. mmaxeyjr 2008-05-11T14:10:42-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3639999#3639999 no, you can fish it through one of the places where wires are already going through. I did it and it works fine. ken240sx 2008-05-11T09:59:43-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3639970#3639970 i have 2 separate rca cables. The ground wire that I did was just to put in a ground wire, not for the amps or anything. So drilling is necessary mmaxeyjr 2008-05-11T09:36:25-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3639947#3639947 Whatever you just did, edit and cut....don't do it again lol. Oh by the way, anytime you're working with the electrons in the car, make sure the negative is disconnected and not touching anything metal.The ground that I was talking about is the one from your amps, you'll need to run one from your amps to the closest metal thing in your hatch area.And do you only have one set of rca or 2 setsif you only have once set then you can run the rca from your deck to one amp, and use the output rca from that amp and hook an rca cable from that amp to the other. Assuming there's an output rca on one of the amps....If there's not an rca output on one of the amps then go on ebay or some place that sells electronics and get an rca splitter. It should plug into the back of your deck where the rca connections are, and it will split into 2 sets of rca cables.And about the power wire, I just found a rubber grommet on the firewall that a wire harness was going through and I shoved it through there and fished it through the other side. Another easy thing to do is find a blank spot on your firewall and drill a hole big enough for the wire to go through. Go down the the hardware store and pick up a rubber grommet that will fit the hole, and then just slide your wire through the hole you made. BUT MAKE SURE BEFORE YOU DRILL THAT THERE'S NOTHING IN THE WAY BEHIND THE WIREWALL. I don't want you drilling a 1/4 hole in your blow motor or vents. And remember, ALWAYS DISCONNECT THE NEGATIVE TERMINAL ON THE BATTERY BEFORE MESSING WITH THE ELECTRONICS....only when you're all done wiring up EVERYTHING, connect the negative back on the battery.ALSO, MAKES SURE THAT WHEN YOU'RE WIRING UP THE POWER WIRE THAT IT THE ENDS DON'T TOUCH ANY METAL.SO BEST BET IS TO DISCONNECT THE BATTERY COMPLETELY, THEN DO THE WIRING, THEN HOOK POS UP ON THE BATTERY, THEN NEG. The ground that I was talking about is the one from your amps, you'll need to run one from your amps to the closest metal thing in your hatch area.
And do you only have one set of rca? or 2 sets?

if you only have once set then you can run the rca from your deck to one amp, and use the output rca from that amp and hook an rca cable from that amp to the other. Assuming there's an output rca on one of the amps....

If there's not an rca output on one of the amps then go on ebay or some place that sells electronics and get an rca splitter. It should plug into the back of your deck where the rca connections are, and it will split into 2 sets of rca cables.

And about the power wire, I just found a rubber grommet on the firewall that a wire harness was going through and I shoved it through there and fished it through the other side. Another easy thing to do is find a blank spot on your firewall and drill a hole big enough for the wire to go through. Go down the the hardware store and pick up a rubber grommet that will fit the hole, and then just slide your wire through the hole you made. BUT MAKE SURE BEFORE YOU DRILL THAT THERE'S NOTHING IN THE WAY BEHIND THE WIREWALL. I don't want you drilling a 1/4 hole in your blow motor or vents.

And remember, ALWAYS DISCONNECT THE NEGATIVE TERMINAL ON THE BATTERY BEFORE MESSING WITH THE ELECTRONICS....only when you're all done wiring up EVERYTHING, connect the negative back on the battery.

ALSO, MAKES SURE THAT WHEN YOU'RE WIRING UP THE POWER WIRE THAT IT THE ENDS DON'T TOUCH ANY METAL.
SO BEST BET IS TO DISCONNECT THE BATTERY COMPLETELY, THEN DO THE WIRING, THEN HOOK POS UP ON THE BATTERY, THEN NEG. ]]> ken240sx 2008-05-11T09:17:45-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3639293#3639293 Thanks man It helped me get a better idea. My headunit only has 2 RCA plugs in the back of it, does this mean that I can only run 1 amplifier Meaning i'll only be able to use the amp(S) to power the subwoofersSo I guess to get it hooked up I just need to run a power wire from the pos. terminal to the trunk.Then rca's from headunit to amplifiers.And then put speaker wire from my amp(s) to my subs. then they should be working rightMy only question is how exactly do I get the power wire inside the vehicle and all the way back Do I have to unbolt something Or can I just shove it through something and get to it somehowAlso:Earlier I added a random ground wire from the negative terminal to a bolt (i think it was the one that holds up the windshield washer fluid pipe) When I did this there was a clicking noise that kept going off. It sounded like it was in the relay box.Then I took off the positive termal and it stopped.Next I put both terminals back on and the noise started again. Then I turned on the car while the noise was going off and it ran fine.So then I shut the car off and the sound was gone. Is this badThe car seems to run fine. I drove it 50 miles today.I know it's a lot of reading but I really appreciate all the help!Thanks So I guess to get it hooked up I just need to run a power wire from the pos. terminal to the trunk.
Then rca's from headunit to amplifiers.
And then put speaker wire from my amp(s) to my subs. then they should be working right?
My only question is how exactly do I get the power wire inside the vehicle and all the way back? Do I have to unbolt something? Or can I just shove it through something and get to it somehow?

Also:
Earlier I added a random ground wire from the negative terminal to a bolt
(i think it was the one that holds up the windshield washer fluid pipe)

When I did this there was a clicking noise that kept going off.
It sounded like it was in the relay box.
Then I took off the positive termal and it stopped.
Next I put both terminals back on and the noise started again.
Then I turned on the car while the noise was going off and it ran fine.
So then I shut the car off and the sound was gone. Is this bad?
The car seems to run fine. I drove it 50 miles today.

I know it's a lot of reading but I really appreciate all the help!
Thanks ]]> mmaxeyjr 2008-05-10T21:45:08-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3638284#3638284 Wiring is the easiest part. You plug the rca cables from your amps into the deck. You also wire the thin remote wire to the acc. wire in your deck's harness or if there's a specified "remote" labeled wire. Basically the remote tells the amp when your car is on, so even the cig lighter wire should work. Pick a spot in the trunk about a 1-3 feet away from your amps where you see a bolt that goes into the frame/chassis, the strut towers work well to. Remove the bolt, get some coarse sand paper and sand the paint off where the bolt hole is...This is where you're going to ground your amp or amps, I don't know how many watts you're running, but I use 0AWG wire(zero gauge) for all wiring like this that I do. Now with the power wire, you're also gonna want a low number gauge for the wire, hook it to your positive terminal on your battery. Make sure there is an inline fuse that is about the same as the combined fuses in your amps. Put the fuse closer to the battery end of the wiring. I slip the wire in through the rubber grommet where the harness goes in to the fuse box. Now make sure that when you're laying down the wires and hiding them under your carpet that the rca wires aren't close to the power, because you may have interference that way. I jsut run the rca's down the middle, and the power wire on the drivers side. **** I forgot, I relocated my battery to the drivers side, so it's going to be opposite for you, run the power into the vehicle where the ECU harness goes into the firewall and keep the wire on the passenger side.Hope this helped. Hope this helped. ]]> ken240sx 2008-05-10T11:34:05-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3638112#3638112 alright thanks for the info guys.another thing i want to do is put in my subs and amps.I have a jvc kameleon head unit, 2 12" JL W3 subs, and 2 sony amplifiers. I had them in my previous car and they worked well together. But idk how to go about wiring this.Also the speakers are 4x6 all the way around rightThanks Modified by mmaxeyjr at 11:08 AM 5/10/2008 another thing i want to do is put in my subs and amps.

I have a jvc kameleon head unit, 2 12" JL W3 subs, and 2 sony amplifiers. I had them in my previous car and they worked well together. But idk how to go about wiring this.

Also the speakers are 4x6 all the way around right?

Thanks

Modified by mmaxeyjr at 11:08 AM 5/10/2008 ]]> mmaxeyjr 2008-05-10T09:38:48-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3637843#3637843 the black lights look nice, but you might get hassled by cops. get a spare set that way you can switch back to stock untinted ones if u need to. theres a perfect set of hatch tails at ez pull White Comet 2008-05-10T05:08:35-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3637759#3637759 Quote, originally posted by mmaxeyjr yah I found it on ebay, idk if it is that specific one, but I like the tint. I don't like the wing, or anything else though haha.I just think tails completely blacked out like that look pretty sweet on a red hatchback idk if I want to do it or not though...Also i'm in need of a complete radiator flush, BADLY! What's the best way to do it on these cars Is there a screw or knob that I break loose and the fluid automatically drains outAlso is there more than 1 screw/knob that I have to break looseShould I use my hose and run water directly through the radiator so it cleans it outDo I have to jack up the carThanks a lot!Modified by mmaxeyjr at 10:05 PM 5/9/2008Best way to do it on your own is to go to your local autoparts store and pick up a coolant flush kit. Follow the instructions on it.There should be a screw on the drivers side of the block somewhere under the exhaust manifold, and then there's a plastic screw on the bottom of the radiator...watch out not to strip it, I almost have mine stripped so I have to be careful.When you're draining, make sure your radiator cap is off, and I'd also disconnect the bottom radiator hose too...it just makes hte job easier. Quote, originally posted by mmaxeyjr raquo;yah I found it on ebay, idk if it is that specific one, but I like the tint. I don't like the wing, or anything else though haha.

I just think tails completely blacked out like that look pretty sweet on a red hatchback idk if I want to do it or not though...

Also i'm in need of a complete radiator flush, BADLY! What's the best way to do it on these cars? Is there a screw or knob that I break loose and the fluid automatically drains out?

Also is there more than 1 screw/knob that I have to break loose?

Should I use my hose and run water directly through the radiator so it cleans it out?

Do I have to jack up the car?

Thanks a lot!

Modified by mmaxeyjr at 10:05 PM 5/9/2008

Best way to do it on your own is to go to your local autoparts store and pick up a coolant flush kit. Follow the instructions on it.
There should be a screw on the drivers side of the block somewhere under the exhaust manifold, and then there's a plastic screw on the bottom of the radiator...watch out not to strip it, I almost have mine stripped so I have to be careful.

When you're draining, make sure your radiator cap is off, and I'd also disconnect the bottom radiator hose too...it just makes hte job easier. ]]> ken240sx 2008-05-10T01:55:10-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3637753#3637753 I like,very clean! ]]> karism 2008-05-10T01:46:24-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3637379#3637379 yah I found it on ebay, idk if it is that specific one, but I like the tint. I don't like the wing, or anything else though haha.I just think tails completely blacked out like that look pretty sweet on a red hatchback idk if I want to do it or not though...Also i'm in need of a complete radiator flush, BADLY! What's the best way to do it on these cars Is there a screw or knob that I break loose and the fluid automatically drains outAlso is there more than 1 screw/knob that I have to break looseShould I use my hose and run water directly through the radiator so it cleans it outDo I have to jack up the carThanks a lot! Modified by mmaxeyjr at 10:05 PM 5/9/2008 I just think tails completely blacked out like that look pretty sweet on a red hatchback idk if I want to do it or not though...

Also i'm in need of a complete radiator flush, BADLY! What's the best way to do it on these cars? Is there a screw or knob that I break loose and the fluid automatically drains out?

Also is there more than 1 screw/knob that I have to break loose?

Should I use my hose and run water directly through the radiator so it cleans it out?

Do I have to jack up the car?

Thanks a lot!

Modified by mmaxeyjr at 10:05 PM 5/9/2008 ]]> mmaxeyjr 2008-05-09T21:46:49-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3636798#3636798 Quote, originally posted by mmaxeyjr It's got a good inspection until May 2009. I want it to look like this. What do you thinkDude! Isn't that the ebay piggy we made fun of last week If it is, its not bad looking but it was overpriced w/ sunk wheels and was being advertised as a showcar... Quote, originally posted by mmaxeyjr raquo;
It's got a good inspection until May 2009.
I want it to look like this. What do you think?

Dude! Isn't that the ebay piggy we made fun of last week? If it is, its not bad looking but it was overpriced w/ sunk wheels and was being advertised as a showcar... ]]> simmode1 2008-05-09T17:02:18-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3636769#3636769 Quote, originally posted by White Comet legally you cant go that dark, but if u dont think cop will hassle you and u can get some one to pass u for inspection go for it It's got a good inspection until May 2009. I want it to look like this. What do you think Quote, originally posted by White Comet raquo;
legally you cant go that dark, but if u dont think cop will hassle you and u can get some one to pass u for inspection go for it

It's got a good inspection until May 2009.

I want it to look like this. What do you think?

]]> mmaxeyjr 2008-05-09T16:49:22-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3636123#3636123 Quote, originally posted by mmaxeyjr I have a question. In the state of Pa, is it legal to make your tailights completely black I want to use dark spraypaint or 5% nightshade and tint my tail lights.legally you cant go that dark, but if u dont think cop will hassle you and u can get some one to pass u for inspection go for it Quote, originally posted by mmaxeyjr raquo;I have a question. In the state of Pa, is it legal to make your tailights completely black? I want to use dark spraypaint or 5% nightshade and tint my tail lights.
legally you cant go that dark, but if u dont think cop will hassle you and u can get some one to pass u for inspection go for it ]]> White Comet 2008-05-09T12:07:22-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3635620#3635620 Quote, originally posted by mmaxeyjr Yeah if I could find the lip for an affordable price i'd definately go for it and put it on right away. If anyone knows where or who I can get one let me know I got one for sale. 50 bucks. Has a couple cracks that can be fixed with body filler/fiberglass. Quote, originally posted by mmaxeyjr raquo;Yeah if I could find the lip for an affordable price i'd definately go for it and put it on right away. If anyone knows where or who I can get one let me know

I got one for sale. 50 bucks. Has a couple cracks that can be fixed with body filler/fiberglass. ]]> fourLUG_hero 2008-05-09T09:09:34-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3635457#3635457 I have a question. In the state of Pa, is it legal to make your tailights completely black I want to use dark spraypaint or 5% nightshade and tint my tail lights. mmaxeyjr 2008-05-09T07:54:02-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3632404#3632404 oh well, i missed it too. i didnt even hear about it White Comet 2008-05-08T09:19:17-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3632076#3632076 yah there was supposed to be a tristate tuners meet at sonic. I didn't get to go though... mmaxeyjr 2008-05-08T07:20:44-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3628990#3628990 ^ i dont know, is there something going down today White Comet 2008-05-07T08:29:43-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3628965#3628965 yah i like the piggy look better than chuki though wc are you going to be at sonic today wc are you going to be at sonic today? ]]> mmaxeyjr 2008-05-07T08:16:21-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3628723#3628723 Quote, originally posted by Cory_Marshall VERY clean 1990.It's nice to see one in that shape. The motor even looks very clean.Their is a FEW 1990's in my town and ALL of them are in totally crappy shape, rotted to hell and they all have those SUPER ugly stock rims on them..its true most are beat to hell, this makes me miss mine. my piggy hatch was super clean and only had 20k on the motor. i vote for putting a chuki bumper on someday Quote, originally posted by Cory_Marshall raquo;VERY clean 1990.

It's nice to see one in that shape. The motor even looks very clean.

Their is a FEW 1990's in my town and ALL of them are in totally crappy shape, rotted to hell and they all have those SUPER ugly stock rims on them..
its true most are beat to hell, this makes me miss mine. my piggy hatch was super clean and only had 20k on the motor. i vote for putting a chuki bumper on someday ]]> White Comet 2008-05-07T05:20:09-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3627756#3627756 haha yah i got lucky and an older lady had mine before me. only thing was she had a dog so there was dog hair in the interior. and now it kinda smells. but fabric stuff like febreeze should fix it.. heres a wanted list:Wire tuckmore Grounding wiresFront lipSprings or Coilovers5 Speed Swap (w/ short throw)Intake / exhaustWheels (extended wheel studs)Fog lightsTinted windowsstereo system - i just need door speakers..

heres a wanted list:

Wire tuck
more Grounding wires
Front lip
Springs or Coilovers
5 Speed Swap (w/ short throw)
Intake / exhaust
Wheels (extended wheel studs)
Fog lights
Tinted windows
stereo system - i just need door speakers..

]]> mmaxeyjr 2008-05-06T20:02:09-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3627546#3627546 nice!!! very nice. I just bought a 90 hatch as well. It's black n kinda busted. Previous owner did some wackness to it! Motor had all this yellow tubing on it, and spray paint!!! runs healthy tho...Also painted interior panels blue! wtf!! didn't even do a good job, time well waisted. and last...they put fake hood scoops! ripped em off right away. I have vision tho, i see the potential.Urs is clean man! Also painted interior panels blue! wtf!! didn't even do a good job, time well waisted. and last...they put fake hood scoops! ripped em off right away. I have vision tho, i see the potential.

Urs is clean man! ]]> sharkerio_coupe 2008-05-06T19:09:38-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3627457#3627457 Quote, originally posted by Cone Junky Looks clean. Now you just need to remove that lower pinstripe and fix your broken headlights...haha thanks, except I like them that way. it's sleepy sometimes Quote, originally posted by Cone Junky raquo;Looks clean. Now you just need to remove that lower pinstripe and fix your broken headlights...

haha thanks, except I like them that way. it's sleepy sometimes ]]> mmaxeyjr 2008-05-06T18:44:39-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3627252#3627252 VERY clean 1990.It's nice to see one in that shape. The motor even looks very clean.Their is a FEW 1990's in my town and ALL of them are in totally crappy shape, rotted to hell and they all have those SUPER ugly stock rims on them.. It's nice to see one in that shape. The motor even looks very clean.

Their is a FEW 1990's in my town and ALL of them are in totally crappy shape, rotted to hell and they all have those SUPER ugly stock rims on them.. ]]> Cory_Marshall 2008-05-06T17:41:06-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3626752#3626752 Looks clean. Now you just need to remove that lower pinstripe and fix your broken headlights... Cone Junky 2008-05-06T14:26:42-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3626741#3626741 yank that AT out of there, other than that, clean fastback. srpowered240sx 2008-05-06T14:24:00-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3626624#3626624 yah i live in lancaster county Modified by mmaxeyjr at 1:52 PM 5/6/2008

Modified by mmaxeyjr at 1:52 PM 5/6/2008 ]]> mmaxeyjr 2008-05-06T13:40:08-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3626604#3626604 Quote, originally posted by hbpignosePA hey looking pretty clean... we dont have PM but try and get in contact w white comet.... he and a bunch of lancaster guys could probably help u outindeed im always down to meet new 240 owners and lend a handQuote, originally posted by mmaxeyjr yah I have a few friends that own 240's and could help me out. I know of 5 240sx owners in my area that are within a 5 minute drive. nice, get a hold of me sometime, i wonder if we know any of the same 240 owners Quote, originally posted by hbpignosePA raquo;hey looking pretty clean... we dont have PM but try and get in contact w white comet.... he and a bunch of lancaster guys could probably help u out

indeed im always down to meet new 240 owners and lend a hand

Quote, originally posted by mmaxeyjr raquo;

yah I have a few friends that own 240's and could help me out. I know of 5 240sx owners in my area that are within a 5 minute drive.

nice, get a hold of me sometime, i wonder if we know any of the same 240 owners ]]> White Comet 2008-05-06T13:31:49-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3622495#3622495 Quote, originally posted by hbpignosePA hey looking pretty clean... we dont have PM but try and get in contact w white comet.... he and a bunch of lancaster guys could probably help u outyah I have a few friends that own 240's and could help me out. I know of 5 240sx owners in my area that are within a 5 minute drive. Quote, originally posted by sommmatt You need a piggy lip hard. haha. Yeah if I could find the lip for an affordable price i'd definately go for it and put it on right away. If anyone knows where or who I can get one let me know Quote, originally posted by hbpignosePA raquo;hey looking pretty clean... we dont have PM but try and get in contact w white comet.... he and a bunch of lancaster guys could probably help u out

yah I have a few friends that own 240's and could help me out. I know of 5 240sx owners in my area that are within a 5 minute drive.

Quote, originally posted by sommmatt raquo;

You need a piggy lip hard. haha.

Yeah if I could find the lip for an affordable price i'd definately go for it and put it on right away. If anyone knows where or who I can get one let me know ]]> mmaxeyjr 2008-05-05T08:25:41-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3622458#3622458 You need a piggy lip hard. haha. sommmatt 2008-05-05T08:09:44-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3622395#3622395 hey looking pretty clean... we dont have PM but try and get in contact w white comet.... he and a bunch of lancaster guys could probably help u out ]]> hbpignosePA 2008-05-05T07:34:55-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3622378#3622378 yes hopefully over the summer. mmaxeyjr 2008-05-05T07:20:07-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3621678#3621678 nice clean hatch, manual swap anytime soon Scuffed_ChukiCoupe 2008-05-04T21:46:56-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3620927#3620927 thanks, yah it really cleaned up well after the wash and wax shined it right up I'm looking for a few parts actually i've already posted in the wtb section.intake, converter(for cone filters), button cover for cruise control or button.thanks

I'm looking for a few parts actually i've already posted in the wtb section.

intake, converter(for cone filters), button cover for cruise control or button.

thanks ]]> mmaxeyjr 2008-05-04T17:52:45-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3620926#3620926 zomg cleannnnn!! love it ]]> EnjoiNismo 2008-05-04T17:52:11-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3620880#3620880 looks nice, I'm hopefully getting a '90 hatch within a week or two. ]]> JewUnit815 2008-05-04T17:30:34-08:00 http://forums.nicoclub.com/zerothread?id=334918;postid=3620873#3620873 Heres some pics of my 1990 240sx. Just cleaned it up. Painted hubcaps and gauge bezzel to match (gunmetal), polish valve cover (more for sale), tune up, waxed it etc..Enjoy, let me know what you think. Enjoy, let me know what you think.

]]> mmaxeyjr 2008-05-04T17:25:36-08:00