Nissan Forums / Infiniti Forums - NICOclub: Engine / Drivetrain (for sale)

KA24DE For Sale

justin505 — 2009-11-22T08:39:37-08:00

I have a ka out of my 95 240. Swapped an s14 sr in it and the ka is sitting in a nice warm van waiting for someone to buy it. I live in Portland, Oregon. Asking $500 obo. I have a cherry pick if someone local needs it put in their vehicle. Shipping could be done as well. Motor is very strong. Ran like a champ 3 weeks ago when I took it out. PM me or email. justinwilks91@hotmail.com Thanks.

NY:WTB rb25 tranny

rbs13det — 2009-11-21T18:50:17-08:00

looking for a good tranny for my rb26 240 swap

Ultimate SR20det swap -Built Motor!

StandardIdiot1 — 2009-11-21T15:16:58-08:00

I have been working on my s14 for some time now and I just happen to change my mind on my motor setup, after I fully built an sr20det with all the bells and whistles. I'm looking to sell the motor tranny wiring harness and ecu as a kit.

Motor Specs
Engine Mods
Crank magna-fluxed and polished
Engine block bored .020 , honed, decked, washed
CP pistons
Brian Crower Rods
ACL Race Rod, Main and thrust
ARP Head Studs
Cometic Metal Head gasket
Moroso Oil Pan
OEM Engine Gasket Kit
Cylinder head decked and washed
5 angle valve job
New valve guides
Brian Crower Valve springs and Titanium Retainers
Port and polish
Intake and exhaust manifolds and gaskets port matched
Brian Crower stage 2 cams
Titek Adjustable Cam gears
garret gt2871r .86
Cams degreed to true TDC
xs power exhaust manifold
Rebuilt Alternator
Rebuilt Starter
Meagan Aluminum pulleys
Circuit sport oil feed and water lines
Powder coated Valve cover
Stock intake manifold glass bead blasted inside and out
Motor fully balanced
act lightweight flywheel
Rps Clutch
New oem water pump

This motor has been properly built, as you can see by the attention to detail in the pictures.

Stock 5 speed trans, cleaned and painted black

Wiring harness professionally redone by Wiring specialties.com

Stock ecu

PS pump, ac compressor also included

Will include Drive shaft shop one piece steel drive shaft and all extra and oem sr20det Parts I have.

Asking $5500 obo, and just because I put obo, don't low ball me please.

Will also accept an ls2 motor trans and harness, or something comparable for trade.

shipping will be at buyers expense, if driving distance is within and hour or too, I can meet.

RB20DET full swap into s13 for sale/part out

carcrzy920 — 2009-11-21T13:06:25-08:00

okay so i have run out of money and need my car back so im pulling out the RB20DET and am just going to put a KA24DE back in it. i just didnt have the money for a few parts that were still needed. the motor only has roughly around 60,000 miles on it. comes with everything needed to swap into a s13 240sx. comes with everything listed. complete RB20DET engine/trans, converted harness, ecu, mafs, full fmic kit, nismo fpr, turbo elbow and down pipe, custom mounting kit to clear steering link, and blue silicone radiator hoses. i have tested compression and all cylinders have great compression. The engine has been well taken care of and comes with a fresh oil change with mobil 1 synthetic 10w-30 and same for trans gear oil 75w-90. the tranny shifts smooth with not a single grind and the clutch still grabs hard. the pics are of the engine when it was in the car i have since taken it out and am trying to find a ka24de to replace it. i am open to trades such as a running ka24de with low miles and cash on your end. i am not looking for any upgrade body/suspension wise since the car is already fairly decked out with all that stuff. this is a crazy good deal for all this so dont let it pass you by. i really dont want to do this but i have to take care of my prioritys first. i would not sell it if i didnt have to. please if you have any questions you can email me or text me at 540-903-4022 names Daniel. pick up only!!! unless you buy parts then i can ship. let me know what parts you want and ill get you a price, but if you buy everything i have listed the price is fairly firm at $1300

FS: Circuit Sports O2 Elimination Downpipe

sinthanius — 2009-11-21T13:04:56-08:00

Greetings !

Up for sale is a Circuit Sports O2 Elimination Downpipe.

Condition: Slightly used

Reason for selling: Parted out my SR20DET, car is gone, parts remain

It retailed for $300 when I originally purchased it, however, I've set up an ebay auction starting at $50. It this point I just want to clear the garage.
Good luck guys!

http://cgi.ebay.com/ebaymotors...99603

VG30E + 5 Speed w/ stage 3 clutch

TJcars2 — 2009-11-21T11:25:01-08:00

Engine runs fine but it needs a head gasket on the left bank.

$400

Will ship if you pay for it.

I need a 5speed kit for an S14

JHavlat48 — 2009-11-21T11:05:04-08:00

i am looking for everything needed for the 5 speed swap..i have a 95 and live in lincoln, Nebraska 68521

looking for

rudolphthered — 2009-11-21T23:26:36-08:00

Hi im looking for a ka24e tranny for a 90 240sx in good condition no grinding ill give about $110 for it plus shipping it to me . thanks

complete sr20det blacktop longblock part out!!!

bigwhiteboybob — 2009-11-22T02:22:32-08:00

All things bought do not include shipping. paypal ready. parts are used but cleaned and are sold as is. but prices as you know are all OBO!!

spun a bearing you can see it on the crank can be resurfaced 50$ obo

needs to be bored over or what ever you want it has small grouves in piston walls. 75$ obo

head is in good shape no known problems. it is completly striped 75$ obo

S13 SR WATER OUTLET PIPE NOT INCLUDED WITH HEAD. 60$ obo
dip stick 10$ obo

upper oil pan 150$ obo

lower oil pan (saw a dent i never new about and a weld about half a inch when i cleaned it) worked perfect for me never a problem. 45$

brain crowler 264's a few months old but had oil deprevation and it wore a little bit down i dont think it will effect there performance because of how little they are worn down. 115$ obo.

great condition blacktop valve cover 85$ obo
timing chain 15$
and tensioner 15$

sr20 crank girdle 45$ obo
crank pulley 15$ obo
misc part make offer

oil pump assemble cover 50$ obo

and theres 2 other parts i dont know what they are called make a offer really need this stuff sold and a few things im not sure on how to price it other then what i've seen on the internet. i checked all over the web and ive listed my parts much lower then any other oem parts that are just like mine but please let me know if im to high on stuff and MAKE A OFFER! cant stress that enough worse i can say is no. but please be reasonable guys. feel free to contact me by either reply to post or sending me a email at bigwhiteboybob@aol.com

Modified by bigwhiteboybob at 5:41 PM 11/20/2009

Modified by bigwhiteboybob at 9:02 PM 11/20/2009

Modified by bigwhiteboybob at 4:07 PM 11/21/2009

Modified by bigwhiteboybob at 3:22 AM 11/22/2009

FS - Tomei CA20 stroker kit

typhoonslippery — 2009-11-20T22:44:37-08:00

FS - Tomei CA20 stroker kit

I am selling a CA20 Tomei stroker kit that I purchased in Japan a few years ago.

It includes a new Tomei CA20 crank, new Tomei 84mm CA20 piston set and used Exedy CA20 6 bolt flywheel with Nismo 3-puck clutch/pressue plate

$2200USD
email me at typhoon_slippery@hotmail.com

Modified by typhoonslippery at 8:21 AM 11/22/2009

Anybody selling any kinds nos warmer kits

Rohanmax14 — 2009-11-20T05:17:58-08:00

I need it for 10-15lb warmer kits.

Z32/N62 MAF works perfect/w pigtail

GTiRSE-R — 2009-11-19T22:21:35-08:00

Maf works perfect I am running one on my SER and I have driven around with it to test it and it works perfect. I want 150 for it.

The pigtail will work its just the plastic where the wire clip goes is broken.

The tag is marked 22680 30P00 A36-000 N62 0224A

NJ: KA24DE complete running engine for sale

Justin35ll — 2009-11-20T14:51:32-08:00

1993 KA24DE for sale. Has 164,000 on it with an auto trans. Burns a little oil.

looking for 300$ OBO will include wire harness and ecu, battery, lower harness, etc.. if wanted

make offers NEED THIS GONE!

Engine is still in my coupe, but I will pull it.

Modified by Justin35ll at 6:12 PM 11/19/2009

APEXI AFC NEO AIR FUEL CONTROLLER UNIVERSAL

streetcustoms — 2009-11-20T16:12:01-08:00

located in tujunga ca 91042

CALL OR TEXT ANYTIME (818)606-1543

BRAND NEW OUT OF BOX

UNIVERSAL FIT

SELLS FOR 450 BRAND NEW SELLING FOR 175

ECU TUNING KIT
&
ENGINE MANAGEMENT
~IN ONE~

A'PEX introduces the first digital fuel computer that combines fuel computer functions with a VTEC engagement controller.

The V-AFC features a user-definable, eight-point, adjustable fuel curve that can be set in 500 RPM increments. The range of fuel adjustment is +/- 50% at each of the user-defined setting points.

The Fuel Adjustment function considers wide/narrow throttle and low/high camshaft settings, from which four different fuel maps are created (wide-low, wide-high, narrow-low, narrow-high).

The integrated VTEC Controller adjusts the point at which the engine switches from the Lo to Hi cam during acceleration, as well as when the engine switches from the Hi to Lo cam during deceleration.

Features:
- Compact "Piggy-Back" Fuel Management Computer (+50% ~ -50%).
- Unit incorporates both the SAFC and the VAFC.
- NEW "Easy" (8-Point) & "Pro" (16 Point) Modes.
- NEW Color FED Display & Interchangeable Button and Background Colors.
- Inverting "anti-glare" screen allowing view from both angles.

Monitor Mode: - RPM, Throttle, Battery Voltage, Correction %, Air Flow %, Pressure (Kpa), Karmann, VTEC

Setting Mode: Air Map, Air Map Graph, Throttle Point, Deceleration Air, VTEC Control, VTEC Unmatch

Etc. Mode: MOdel Select, Mode Select, Sensor Select, Analog Select, Warning Set, Display Set, Sensor Check

CT Fidanza flywheel and Centerforce clutch for ka24de

kpariaug — 2009-11-20T21:55:03-08:00

Selling my setup everything is in VERY good condition almost new, local pickup is available just dont pay the shipping amount. LOTS or high res pics in the gallery on the page.

thanks

http://cgi.ebay.com/ebaymotors...lling

SC New Garrett GT2835R 700.00 Must sell

BenjiD — 2009-11-21T10:42:33-08:00

Brand new Garrett GT3582R
GT2835R - 420 PS Output

COMPRESSOR:
-Wheel- 56 Trim - 53.1 Inducer / 71.1 Major
-Housing- 100 Inlet / 50 Outlet - 0.50 A/R
TURBINE:
-Wheel- 90 Trim - 56.5 Major / 53.6 Exducer
Exhaust Housing .82 GT35 T3 Flange

Email motorhead_s13@yahoo.com

Modified by BenjiD at 5:46 PM 11/19/2009

RB25DET TIMING Idler & Tensioner pulley and VALVE COVER Gasket - OEM BRAND NEW

gt4788 — 2009-11-19T11:01:08-08:00

Hi,

Up for sale is the following:

RB25DET Timing Idler and Tensioner pulley's (Brand New OEM): $50
for both

RB25DET Valve Cover Gasket (Brand New OEM): $35

I have sold my car and have no need for these anymore.

You can reach me at:407-953-3175

Thanks

Modified by gt4788 at 3:42 PM 11/19/2009

z32 tt engine with around 20k from nissan rebuild

az4speed* — 2009-11-19T10:38:50-08:00

i have a twin turbo engine with 20k miles from rebuild but it seems that the 4k that were paid to the dealer were not enough to replace the oil pump so one of the turbos blew and i took it out. after a quick diagnostic we decided that the oil pump need to be replaced no damage was done to the bearing but i still sent the crank shaft to machine shop for a polish then a friend that works at a dismantling shop found me a jdm engine so i got it. i had already ordered some used jdm turbos for the original motor, i still have the old engine but is just there collecting dust when some one else could use it that's when i decided to sell to get some cash so i can get other parts that would be usable for my car here are some pictures email az4speed@ymail.com

Modified by az4speed* at 10:44 AM 11/19/2009

Modified by az4speed* at 10:44 AM 11/19/2009

Drain plug gaskets (crush washers) NEW! OE nissan part

92OCC — 2009-11-20T11:46:09-08:00

I have 6 packs of 10 available. These are BRAND NEW ready to go on.. Not aftermarket, Brand new nissan washers.

$5 shipped for a pack of 10

WTB: RB20DET Harness

KATPower — 2009-11-19T08:03:27-08:00

Found One Please Delete

Modified by KATPower at 11:47 AM 11/20/2009

FL: s13 catback exhaust 3"-3.5" No Ship

Nunook — 2009-11-19T07:58:00-08:00

Some how it double posted, so i edited it. Thanks.

Modified by Nunook at 5:05 AM 11/19/2009

FL: s13 catback exhaust 3"-3.5" No Ship

Nunook — 2009-11-22T06:17:08-08:00

ok guys im getting rid of my exhaust due to me buying another for the wrong reasons. fits great under the car. has some scratches on the bottom side, other than that nothing is wrong with it. I had it for one year and all the scratches are from before I got it.

It is a jdm jasma exhaust. One piece cat-back mandrel pipes with clean welds. 3" from cat to silencer(think its a hks) and 3.5" to the canister. 5" tip. quieter then the blitz I have on now, and flows good.

asking $125 obo Post or PM

http://c3.ac-images.myspacecdn...a.jpg

http://c2.ac-images.myspacecdn...9.jpg

http://c2.ac-images.myspacecdn...d.jpg

Modified by Nunook at 4:29 AM 11/20/2009

Modified by Nunook at 3:14 AM 11/22/2009

Parts for sale, ka, sr make offers! Will ship!

OM3GA — 2009-11-19T01:37:27-08:00

Top Speed S14 SR Throttle pulley wheel (Brand new)-$25obo

Stock DOHC KA fuel pump Guaranteed working-OFFER

Basically Brand new Stock S13 SR20DET Intake manifold 100% clean-OFFER

Polished Shaved S13 KA24DE Valve cover-OFFER

KA Starter Guaranteed working-OFFER

Stock SR Blacktop Turbo Elbow (fat o2 sensor included)-OFFER

1000 miles on a brand new KA24DE Coil-OFFER

3000 miles on Magnecor 8.5mm Spark plug wires-OFFER

S13 KA Manual Transmission inspection plate(goes between block and tranny)-OFFER

Red Top SR20DET ECU Guaranteed working(if not your money back haha)-OFFER

Make offers on everything, i may be down for trades depending on what it is.

Lets see you close this one Nicky Poo :wub:

NEW - sr20det Greddy RAS

Kalypso — 2009-11-20T20:39:05-08:00

(Greddy - sr20det Rocker Arm Stoppers)

Brand new, never installed... they simply sat on my shelf.

47 shipped

RAS, 180sx, 240sx, s13, s14, sr20det, sr20

s13 sr20det altenator

Kalypso — 2009-11-20T20:16:57-08:00

pulled from my sr20 part out. works fine

60 shipped...

Modified by Kalypso at 11:18 PM 11/20/2009

RB and SR STUFF TURBO's,ECU's AND MORE FORSALE CA SOCAL!!!!!!!!!

preston240sx — 2009-11-21T10:48:16-08:00

Havea bunch of stuff in my garage that me and my room mate are trying to get rid of he has a sr and i have a rb and we have extra parts that we are looking to get rid of so if you see something u like lemme know ..... if i dont have it listed ask me i may have it thx

2 -oem stock T-3 turbos both are ready for install both have minimal shaft play both have alotta life left.....165 each

1 oem stock wiring harness not cut .......170obo SOLD
1 oem rb20det turbo manifold ...... best offer

1 oem rb20det a/c compressor with uncut lines still attached ...... 75 shipped

1 oem crossover pipe ....30 shipped

1 oem blank timing cover "does say which rb you have"......35 obo shipped

1 oem hicas steering pump with brackets great shape awesome condition im running one on my car they work just fine ........60 shipped SOLD

1 set oem block mounts aluminum.. obo

1 oem rb25 coilpack cover 20........................shipped

1 oem turbo intake piping 30 ...............shipped

12.....270cc rb20det turbo injectors 50 a set obo shipped

call or text for info 4129656388 thx

and here's the sr stuff

370cc injectors like they have brand new o rings ... 70shipped

jdm hood props make off .....

1 sr coilpack 25 shipped

sr20 igniter 40 shipped

t25 little to min shaft play alotta life 125 shipped

sr20det stock maf with plug 60 shipped

2 ecu's $90 each shipped,EC

Modified by preston240sx at 4:49 PM 11/19/2009

f/s brand new never used 740CC DW injectors. 280 shipped

((sr)) kelly — 2009-11-20T15:03:06-08:00

selling these DW injectors because i got some 850s in a trade.

i installed these on my built engine that is outside of my car, They have never seen fuel

email is srkoukimonsta@gmail.com

KA24DE/T for sale and turbo kit

troll's 240sx — 2009-11-20T08:43:20-08:00

I have a rebuilt KA with about 5000 miles on it for 400 picked up, if you want it shipped you will have to set up something because I have never shipped anything this heavy. KA has fully balanced internals while everything was attached i think. Crank, stock rods, Arias 8.5 pistons, flywheel and pressure plate all have material taken off and balance together. Cometic head gasket and compression reads 140 psi across all four the last time it ran which was a year ago. Long story short it is now out of the car and collecting dust.

Incomplete turbo kit for sale 1000 takes everything or part out.

T3/T4 Hybrid turbo by Air research single ball bearing A/R 47/60 300
Top mount manifold 50
JWT Fuel rail 100
JWT ECU 300
MSD 50lbs injectors 100
Aeromotive adjustable FPR 100
Oil cooler with lines and adapter 100
Z32 MAF with filter 100
Greddy intercooler with hacked up pipings 150
Custom exit pipe to Megan downpipe 50
SAFC 2 black w/most of the wires 100

Also a Blown KA24de (prob ringlands) with new replacement pistons for 100, this one had about 75000 miles on it.

Both are from S14.

NJ: Kaaz 2 way diff

alwaysS13 — 2009-11-18T20:02:31-08:00

ITEM: Kaaz 2 way diff
PRICE: 600 obo
SHIPPING: No, can meet within reasonable distance
DESCRIPTION: Used Kaaz 2 way diff in good working condition
PICTURES: Will have them up tomorrow, but you know what it looks like

CONTACT INFORMATION:
NAME: Matt
LOCATION: Union County NJ
EMAIL: mpowell558@yahoo.com
PAYMENT OPTIONS: Paypal, cash

S14 SR20DET Turbo lines and S14 Sr20DET CATBACK EXHAUST

Kaforlife — 2009-11-21T16:29:41-08:00

I have a set of stock s14 sr20 oil and coolant hard lines with all hardware expect for one washer for a coolant line. Selling for 35 Shipped OBO

Also selling an almost perfect no name 3" exhaust just has a few scratches from being in my garage for a while. I have a pic of what it looks like on the car and also a sound clip. ( My friend has the exact same exhaust on his car now) selling for $125 + shipping OBO

Modified by Kaforlife at 3:39 PM 11/19/2009

or: datsun 1600 su carbs and intake

67 411 — 2009-11-19T16:15:18-08:00

pair of su's from a datsun r16 good condition both complete 200 shipped obo

$50 Shipped For a New BOV

Kaforlife — 2009-11-21T16:28:44-08:00

I'm selling a brand new HKS knock off BOV. I dont know what brand this is, I have all the parts also have a flange for it. Its not picture because its at my friends house but it does come with one. Looking to get 50 shipped for this.

Thanks for Looking
Ken
tkshoesusa@yahoo.com

Stillen high flow cats for 2007-2009 VQ35HR and VQ37VHR for sale.

pennywise1971 — 2009-11-20T11:01:27-08:00

I had these Stillen HFC installed on my car for 300 miles. I need to sell them for financial reasons. They are in perfect condition. They fit 2007-2009 Nissan 350Z + 370Z and Infiniti G35 + G37. Engines they fit are VQ35HR and VQ37VHR. Stillen part# 503436. I would like $350 shipped or best offer. Contact me at: hackwarren@yahoo.com

[IMG][/IMG][IMG][IMG][/IMG][/IMG]

Modified by pennywise1971 at 6:36 PM 11/18/2009

Cluth pedal, 5speed Crossmem

aaronscomp — 2009-11-19T16:04:45-08:00

Ok i have a s13 cluth pedal for sale for 80obo and a 5speed crossmember for sale for $40obo just let me no email me at aaron.kindall@gmail.com

FS: SR20det Intake Manifold

forcemotorsports1 — 2009-11-18T14:06:53-08:00

For Sale SR20det Intake Manifold.
Was taken off of my RED TOP sr20.
$195

shoot me a message if you have any questions at all.

HUGE SALE: 90% Greddy Turbo Kit (KA24DE), Clutch, Aero

GTS — 2009-11-20T00:23:24-08:00

All items are located in Toronto, Ontario, Canada. Will ship or meet up at buyer's expense.

90% complete Greddy Turbo Kit for KA24DE
Price: $2500
Items are used, in good condition, there are many people who have seen this setup and I'm quite confident that they will vouch for how reliable this powerful setup is. Running at 10psi, I was at 260whp and 270+ft/lbs - these figures can be verified by a number of members on this forum.

Greddy Cast iron manifold, T3, cast iron = unbreakable
Greddy TD06 20G Actuator Style Turbo + elbow - great condition, no play, T3 flange
Larger 370cc Top-feed Injectors w/ hi-flow fuel rail (Does not include injector connectors)
preprogrammed E-Manage Piggy back computer
Airnix Air intake system
Oil feed + return lines
Hotpipe w/ Greddy Type RS BOV
Damage coldpipe (Can be used with some creative bending)
Megan Racing Front Mount intercooler (damage, I can have it fix, or you can fix it yourself)

The only thing this is missing are the injector connectors. If you can find other connectors that work the the RC injectors - great! If not, I'd suggesting getting new injectors anyway (370cc is a bit too small if you want to turn up the boost and run this turbo in its most effective range).

Item: S14 Rear Strut Bar + C-pillar bar
Price: $120 for both, $70 each seperately

Item: Stage 4 Competition Clutch + lightweight flywheel
NEW, NEVER USED
Price: $600 for both
Separately: $400 for clutch and pressure plate, $300 for flywheel

Products

Item: Nissan Brake Cylinder
I'm not sure which car it is from, but it does have ABS and it is bigger than stock S14 BMC
Price: $80

Item: Kouki S14 JDM Front Grill
2 tabs are missing from the back, but the grille can be held in place by zipties (invisibly). I konw this because this is what I did
Price: $120

Item: Nismo 270R Rear Bumper + Valences - Replica
Price: $300

It's made from plastic - not as brittle as fiberglass

Item: S14 USDM 5 lug FRONT calipers + pads + rotors
Asking Price: $125 OBO
Condition: Used

5lug USDM brakes for S14. Comes with everything but lines.

Fully Built Sleeved Mazworx 2.2L Sr20det block / exedy twin disk / peakboost

srdub-t — 2009-11-21T12:21:04-08:00

This block is freshly built with all bran new parts and has never been fired up. All the machining was done at mazworx witch includes the Darton 90mm sleeve install, oil groove machining the mains for better oiling, 1/2 inch head stud upgrade so the head wont lift under high boost (arp 1/2 inch heads studs included), front cover decked with block. This service costed me $2355 for just the bare block, now lets get to the internals: custom 9:1 compression CP pistons with rings, lateral gasport, double pin oiler, accumulator grooves, heavy duty wrist pins and locks (costed $750), carrillo Rods good to 1000 hp ($1000), calico coated ACL main bearings and thrust bearings, New oem timing chain and upgraded metal guides. The bottom end was assembled at rebello racing, they have been around and building nissan engines for 25 years and they are simply the best (assembly cost $1000). This engine has been with only the best machinest and builders with only the best parts used, Iv spent over $5000 to get this bottom end built and ready for 800 whp easy. this engine is ready for serious boost + nitrouse or any thing anyone wants to use it for.. the big bore brought it to a 2.2L and since the stroke is the same you can rev this engine to 9000 rpm with out a sweat. Im asking a very very reasonable price of 3600 including a bran new ati super damper pulley ($450) you could never replicate this build for this price. i also have a freshly rebuilt exedy twin disk for $750 shipped, and peakboost manifold with elbow and dp for $650 plus shipping used for less than 500 miles. Call me with any questions at 925 788 9163.

PA: KA24E stuff and 2 transmissions!! NO SHIPPING!!

helluvasinger — 2009-11-18T12:37:59-08:00

I have an 89 KA24E that is leaking antifreeze.. I was told it was a hole in the front cover, but could be a hole in the block. $200 obo for the complete motor, or I will part out. Head is good, alternator, starter, a/c is ice cold... everything works..

Also I have the Auto trans that is in the car, shifts a little hard from 1st to 2nd.. but will sell for $150 obo..

And I also have an S13 KA24DE manual trans that I will sell for $100 firm..

NO SHIPPING!!! I'm in the Harrisburg, PA area!!

shoot me an email.. exiesrockme@yahoo.com

s13 blacktop longblock parts for sale

bigwhiteboybob — 2009-11-18T02:08:10-08:00

here is some pictures of the parts i have all the parts to the long block for sale. the motor spun a bearing and i took it to the machine shop to get a bored and then just decided to go with another stock long block because of the money factor. crank is fine but would need to be redone to use it and the block has small groves in 3 of the piston walls it would NEED a bore to be good again.

But like i said i will have more pictures available soon but what is for sale is a complete long block that has been take apart and each part individually cleaned.

if you have any questions about what i have either post them or email to bigwhiteboybob@aol.com

im not sure off pricing im willing to let this stuff go for cheap because its just sitting in my garage right now give me a offer and we will talk about it. but im not trying to hold onto anything.

I will not pay shipping cost on the larger items. if you buy it you are responsible for shipping cost.

NSW: D21 Performance parts INT. Postage available. Z24

Rocket31 — 2009-11-21T21:27:21-08:00

Performance Headers 4/2/1 with 2 1/4 inch outlet with flange

Decent Crow cam (not too mild but not to wild (generic pic but will come with box and sticker (Y))

Distributor (8 plug) vacuum advance removed, weighted advance installed (for use with side drafts etc)

Reco head minus valves + raised compression ratio.

TWIN WEBER Side draft manifold. (w/o webers)

WEBER air filters x2

Thermo/electirc fan mounted in shroud

Thermostat with switch for thermo fan ( for use with side draft etc)

Halo/ angel eye headlights plus bulbs

+ lots of engine accessories

PM OR REPLY TO TOPIC for prices and postings

Modified by Rocket31 at 1:13 AM 11/18/2009

NY/ FS:93-98 nissan 240sx power steering reservoir with lines uncut

nyc240sx — 2009-11-18T00:11:25-08:00

Mint shape power steering reservoir for the nissan 240sx years 93-98 it has both of the lines still attached to it and uncut $25 if interested my email is lznyc2007@gmail.com
thanks

FS:U13 Turbo manifold and J-pipe

sr20fanp11 — 2009-11-17T23:17:32-08:00

I have a U13 turbo mani and a j-pipe. these are extra parts and I don't need them anymore.I've personally never used them since I bought it from a friend. Couldn't finish my turbo setup due to bills.

BOV - SOLD
J-pipe - 45shipped
Turbo mani - 100shipped
130shipped for both jpipe and manifold

[IMG]http://i882.photobucket.com/albums/ac26/mikedes28/110820

Tons of oem parts... 240sx, sr20det, 350z

redsx13 — 2009-11-17T23:17:26-08:00

-240sx oem parts-
S13 hatch Aztec red rear bumper-30$
S13 Ka24de flywheel (turned)-40$
S13 Brake master cylinder - 25$
S13 headlight motor R or L -20$
S13 brake booster -20$
S13 front signals R or L - 20$
S13 oem steel wheels (4) -100$
S13 sway bars F or R- 15$
S13 radiator -40$
S13 oem coilovers (each) -15$
S13 hatch tail lights (each)- 25$
S13 seats (each)- 25$
S13 rear upper c-arm (each) -20$
S13 fuel pump- 15$
S13 float assem. (fuel gauge)- 15$
S13 ka24de starter- 25$
S13 ka24de ignitor- 10$
S13 front markers (smoked) - 20$
S13 manual trans- 125$
S13 wiper motor- 20$
S13 ka24de ecu- 40$
S13 ka24de maf- 35$

-Sr20det parts-
Jdm Kiwi exhaust manifold -35$
Cam angle sensor- 100$
oem sr20det radiator -50$
oem sr20det radiator hoses -20$
oem fan shrowed -20$
oem bov - 30$
Intake pipe- 30$
oem hotpipe -30$
aftermaket RHD turbo elbow- 30$

-350z oem parts-
Coil packs (each)- 40$
Upper plenum (04)- 40$
Lower plenum (04)- 40$
Injectors (each) 15$
longblock (has rod knock)- 400$

-350z aftermarket parts-
JP tuning front bumper - 100$
JP tuning rear add-on - 50$
Nismo v1 front bumper- 60$

You can email me at D-sport@live.com or call/text me at 818-451-9140 (prefer text)

-Pics available to SERIOUS buyers only upon request
-I dont have any other parts other than whats listed, please dont ask me for other parts.

FS:Garrett T04S

sr20fanp11 — 2009-11-20T12:17:02-08:00

250shipped 220 local pick up
This is a Garrett TO4S 60-1 Comp wheel, on a T31 T3 stage 3 turbine wheel in a T3 turbine housing. The stg3 T31 turbine wheel is good for faster spool up. This turbo is like a journal bearing version of a gt30. Since this one has a .82 hot side it can produce about 500-525whp safely.Turbo was used for about 300miles from being brand new. Turbo is still in good condition.No shaft play at all.You can look up this turbo.These turbo brand new with the newer design are about $1000+. After research I found this turbo new for about $600. Please email me at nismofanatics13@yahoo.com if you're interested. Thanks for looking

Driveshaft shop axles rated for 650whp

Rubenonamission — 2009-11-22T07:25:47-08:00

these are new Driveshaft shop axles rated for 650whp(these will fit s13/s14), they have a 1 year warranty bought them for $986 asking $700obo+shipping call me up 209-409-6440

Modified by Rubenonamission at 9:08 PM 11/17/2009

KAAZ 1.5 way lsd complete pumkin

Rubenonamission — 2009-11-17T20:56:59-08:00

KAAZ 1.5 way lsd complete pumkin, used it on my s14 very low miles works perfect $600obo+shipping call me up 209-409-6440

240 parts in nj take a look

89porkchop — 2009-11-17T17:55:33-08:00

Stock flywheel-20
Open diff-25
6 bolt axles-20
5 speed tranny-75
Blue interior panels-whatever
Stock teardrops-5 each tires are bald.i have two steelies also
some brake calipers
brake master cylinder-10

parts located in trenton.email me for pics. i will trade toward a paintball gun or car cd player. let me know.

jper747@aol.com

Used 3.5 injectors 02 03 in rail Cheap!!

aQ45Dude — 2009-11-17T17:49:23-08:00

Hey i have a set of injectors on ebay for 02 03 maxima and murano
part number FBJC101 Thanks for looking! also have coil packs for the same app. http://cgi.ebay.com/ebaymotors...%3AIT

FS: Super Fresh HKS GT2540 & Garrett T25 Turbos

whatsaturbo — 2009-11-20T23:55:30-08:00

Location: Kill Devil Hills, NC
Contact: unsceneperformance@yahoo.com
text: 252-367-7014
NEW PRICES

HKS GT2540 Turbo
Like brand new. Was used for less than 2K miles. Has absolutely NO shaft play. It is extremely clean, no rust, dirt, or oil. .64 Dual BB.
$900 shipped

Garrett TR0760 T25 Turbo
Could use new seals.
$40 obo shipped

Modified by whatsaturbo at 12:30 PM 11/20/2009

Fs-Brand new AEM Uego

bigstan — 2009-11-17T14:29:24-08:00

I have a brand new still in the box AEM UEGO wideband for $170

FS-Brand New CP pistons

bigstan — 2009-11-17T14:17:53-08:00

I have a set of brand new still in the box CP pistons SR20DET 86mm 9:1 for $450

PA: driveshaft, rad, fuel (ca), ac. can ship

bersh240 — 2009-11-17T13:28:28-08:00

s13 driveshaft. manuel tranny.

CA in tank with floater and everything.
AC. i think its everything.
.
shoot me an offer. no idea what anythings worth. email me or post on here. ill get back to you. thanks

Modified by bersh240 at 12:22 PM 11/20/2009

Modified by bersh240 at 12:23 PM 11/20/2009

KA stuff: injectors, ecu, SOHC coil. (PA)

Didderson — 2009-11-17T07:19:43-08:00

injectors: For a DOHC KA24DE engine. Probably the same part as the sohc KA but I'm not sure. 3 of them have the tip plastic things but one doesn't because it was broken in shipping when I bought them. 25+ship obo for all 4.

KA24E ignition coil. asking 10 plus ship.

KA24E ecu. Manual trans. Asking 25+ship

fs 2 2005 nissan titan motors

uwantnone — 2009-11-17T05:23:50-08:00

I have two 5.6 nissan titan motors less intakes manifolds. one has 65k and one has 88k. I bought them to do a swap and lost interest. my loss ur gain.

$800ea
if your interested make me a offer!

FS: [WA] Massive items FS, lots BNIB, great deals take a look!

SWIFT_DRIFT — 2009-11-18T19:06:33-08:00

i have a lot of stuff i'm going to try and sell at one time here. nothing is in any specific order so yeah... everything is brand new besides the obvious items! most prices will include shipping and paypal so pay attention. PM ME FOR FASTEST RESPONSE this stuff is priced to MOVE!

1. Tomei N2 oil block for sr20. brand new in box. $180 shipped/paypaled

2. Tomei Poncams for sr20 - SOLD!

3. SPL urethane transmission mount - SOLD!

4. Kazama sr20 solid engine mounts. brand new in box. $240 shipped/paypaled

5. Apexi sr20 metal head gasket. size is 86x0.8mm and it's brand new in packaging. $170 shipped/paypaled

6. Apexi Z32 power flow intake kit - SOLD!

7. Maxworx spec ARP headstud kit for sr20. brand new ready to go. $170 shipped/paypaled

8. Greddy sr20 oil pan. brand new in box (not pictured). $300 shipped/paypaled

9. Koyo s13 sr20 aluminum radiator. brand new in box, just removed like that for pictures. $280 shipped/paypaled

10. Samco sr20 radiator hoses - SOLD!

ok that's it for now. ALSO NO TRADES. NONE, ZERO. buying multiple items may save you more money on shipping! if you have a good offer and can pay asap i may accept it.

thanks for looking and reply here or email to astunnedguy (at) hotmail.com

Modified by SWIFT_DRIFT at 10:50 PM 11/21/2009

KA24E Turbo kit

aziankingz — 2009-11-21T08:30:35-08:00

Hi All, spent the past year and a half piecing together the perfect turbo setup for my KA24E s13 but had a change of heart and will be parting from the 240sx scene.

These are the parts included in this turbo kit - NOW PARTING OUT:

Holset H1c Turbo (rebuilt with zero miles and no shaft play) - $325 BUY WITH DOWNPIPE FOR $450 PLUS SHIPPING
Custom manifold (just needs new studs) - Sold!
dsm 450cc blue tops with pigtails and resistors - $70 (4 with pigtails/connectors) - pending
Custom downpipe with 3" vband to bolt to turbo - $140
Braided stainless steel feed line - $60
EARLS stainless steel oil return line - $40
Oil pan with bung welded on (ka24e oil pan) - $45
Z32 MAF with pigtail - Sold
JWT ECU - tuned for dsm 450cc inj/Z32 MAF/no speed limit/93 octane only - $425 shipped
Tial 38mm external wastegate with fire ring(new) - Sold
Dump tube - $25 shipped
Ebay intercooler - $80
SR20 Intercooler piping kit with couplings/clamps - $80 shipped
1g dsm bov - Sold
Autometer boost gauge ($30) and oil pressure gauge ($30) with gauge pod ($15) - $75 shipped
AEM UEGO wideband - Sold
Blitz Dual TT DC II turbo timer (with harness) - $55 shipped
Nismo type-A adjustable FPR - $75
Marshall Fuel pressure gauge - $25
F1 Racing Stage 3 clutch kit - $95
Taurus electric fan (brand new) - Sold

Also have:

Brand new JGS polyurethane engine mounts - $90 shipped
New Tranny mount - $35 shipped

Brand new Megan S14/S13 RUCAs - $100 shipped

Please contact me via PM, Aim at aziankingz and/or email at chrisy783@gmail.com

Pictures:

Thanks!

Modified by aziankingz at 9:59 PM 11/16/2009

Modified by aziankingz at 10:04 PM 11/16/2009

Modified by aziankingz at 5:12 AM 11/17/2009

Modified by aziankingz at 4:38 PM 11/17/2009

Modified by aziankingz at 4:48 PM 11/17/2009

Modified by aziankingz at 9:07 PM 11/17/2009

Modified by aziankingz at 9:10 PM 11/17/2009

Modified by aziankingz at 8:32 PM 11/19/2009

Modified by aziankingz at 8:30 AM 11/21/2009

95 240sx clutch & brake pedals,master,booster,drive shaft.

69SSS — 2009-11-16T21:19:13-08:00

95 240sx 5 speed conversion,5speed drive shaft,brake booster,and rear calipers,make offer .
e-mail for pics. Thank you

NJ: Kaaz 2 way diff

alwaysS13 — 2009-11-16T19:48:26-08:00

CONTACT INFORMATION:
NAME: Matt
LOCATION: Union County NJ
EMAIL: mpowell558@yahoo.com
PAYMENT OPTIONS: Paypal, cash

s14/s13 parts

movesalot — 2009-11-20T09:43:03-08:00

I traded my 14 for an ae86, so I've got some aftermarket and stock parts left from the Nissan. I'd rather this stuff be picked up, I live in Orlando around the Waterford Lakes area. If you want it shipped, just pay for it. I believe this is everything....

'95 de s14 parts:
- Megan n/a catback exhaust, bought a couple months ago off Enjuku: $275
- Stock open diff: $OBO
- Clutch/flywheel: $OBO
- A/C compressor: $OBO
- Exhaust mani w/ heat shield: $OBO
- Downpipe: $OBO
- Brackets: $OBO
- One complete stock intake plus a few extra pieces from another: $OBO
- Fan shroud: $OBO
- Radiator (overflow nozzle broken off and pinhole sized hole on top that's been JB welded): $OBO

'91 de s13 parts:
- Tranny: $100
- Intake mani (taken apart): $OBO
- Alternator: $OBO
- Motor mounts: $OBO
- Upper harness: $OBO
- Lower harness (cut): $OBO

I've got a few extra parts that I got w/ the Corolla trade. I'll make a list of those things as well. Thanks for looking, and again, pics of everthing/anything upon request.

- Josh
email: honda10secivic@hotmail.com.....really old email haha
cell: (407) 446-3836.....unlimited text

VA: SR20DET OEM MANIFOLD MINT LOOKS BRAND NEW!

splintercell — 2009-11-18T18:44:49-08:00

JARED HAGEMAN
BOWLING GREEN, VA
804-366-6272
50.00 FREE SHIP!! OBO
I had this professionally sand blasted and i immediately used high temp cast blast 1500* to protect the surface. i put 4 coats on this for even coverage.

when i get parts i believe in cleaning them and making sure they look good for the next person.

rb20 stock turbo

pat1 — 2009-11-16T17:52:47-08:00

rb20det stock turbo

very little play
no smoking or leaking oil
I just pulled it off my running rb today
only ran stock boost

125.00 plus shipping

F/S

youngs13lover — 2009-11-16T17:24:05-08:00

F/S
1 S13 Alternator $30
1 S13 Starter $30
2 S13 Stock Exhaust Manifolds - 1 Stock Downpipe
1 S13 Intake Manifold w/ Trottle body And I Have plenum Gaskets As Well
1 S13 Stock Fuel Pump $25
2 KA Fuel Rails w/ Injectors all noid tested - $20 Each/$25 shipped ea
1 92 S13 Tranny Perfect No Grinds or Anything w/ Shifter - $100
1 KA24DE Hotshot Headers for S13/S14 with new o2 sensor - $150

IF IT HAS A PRICE ITS FIRM IF IT DOESNT ITS OBO ALL NEED TO BE PICKED UP. IN ORLANDO/KISSIMMEE AREA..

PRICES ARE NOT WITH SHIPPING except injectors with rails

THANK YOU COME AGAIN(LOL)

PM ME

FS : HKS SSQV BLOW OFF VALVE $130 OBO

silviaz13 — 2009-11-20T13:41:02-08:00

i have a HKS SSQV VERSION 2 BOV for sell

100% AUTH and brand new

$130 or best offer

located at rosemead 91770

pm or e-mail me for details

silviaz145@yahoo.com

MD: J30 LSD & Bumper OBO

Starclassicbb — 2009-11-17T15:44:24-08:00

I have for sale a J30 LSD with the 5 bolts I'm don't know the miles on it but all it needs are axles if anyone is planning to put a J30 LSD on the S13 this one will work like a said all you need are the axles n change the back plate cover from the S13 n you ready to go!! I also have pignose bumper with no lip, paint it's cracking but all it need is to be sanded I also have a front mount intercooler with no endtanks (not pictured) in good conditions I'm asking $100.00 for it Endtanks usually go for 27 or 30 each depending how big u want the inlet... I'm only accept Cash Pick up only soo that means NO SHIPPING!!!!

$30.00 or best offer

$100.00 or I will trade for lowering springs or exhaust (for S13)

Modified by Starclassicbb at 6:16 AM 11/19/2009

Arias, Fidanza, Eagle, AMS

madthrillzchills — 2009-11-21T20:19:11-08:00

Prices lowered. Plus im paying shipping and the 3% pay pal fee..

Hi im selling alot of parts that i have accumulated. I've planned to put this
all together but i have to deploy again so instead of storing and rusting or getting stolen all my sutff im selling and plan on getting something else...

All prices are open to offers...

AMS- Arias .20 pistons w rings 380 shipped
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

Eagle rods w ARP bolts 220 shipped
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
Spec Clutch 250 shipped
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

Fidanza flywheel 230 shipped
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
Supertech Valves intake 110shipped
Supertech Valves exhaust 110 shipped
^^^^220 shipped for both^^^^
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]

AMS timing chain set COMPLETE 280 shipped
[IMG][/IMG]

AMS Oil pump set COMPLETE 95 shipped

Calico coated bearings (KA24DE Main & Rod) 100 shipped

ARP Head studs (KA) 90shipped

Gasket set *Minus Valve Stem Caps* 60 shipped
Cometic headgasket 60 shipped
^^^^get both for 100 shipped^^^^

Please email me at madthrillzchills@yahoo.com for the fastest response and /or more pictures.....found out how to add photos
Modified by madthrillzchills at 1:30 PM 11/16/2009

Modified by madthrillzchills at 12:46 PM 11/17/2009

Modified by madthrillzchills at 12:47 PM 11/17/2009

Modified by madthrillzchills at 1:19 PM 11/17/2009

Modified by madthrillzchills at 12:11 PM 11/20/2009

s14 zenki AC system

koukizilla — 2009-11-16T12:53:44-08:00

everything is included, lines, hoses, condenser, etc.

i have no idea how much to ask so please throw me some offers, id love to sell it as a unit

CA: SR T25 Fully Rebuilt and Balanced

let5l1de — 2009-11-16T19:20:29-08:00

Fully Rebuilt and Balanced SR T25 with 0mi. Rebuilt just last week right after SEMA show.

270 obo - make an offer! may meet 1/2 way up to 10mi distance.

If rebuilding services are needed, please contact me @ 626.512.3246

~mario

FS: RB25 TUBULAR MANIFOLD

s13_maniacs — 2009-11-16T15:37:21-08:00

Up for sale a custom made tubular manifold... the manifold its in awesome condition, its SS, clears everything as you can see in the pictures and if you need the down pipe I can include it for a bit extra... reason for sale its that I wanna try a new setup with a short manifold since im not draging anymore... here are some pics...

Thanks!!! Mayol... 703-677-5029 If i dont answer pls leave a messege

450 shipped OBO or willing to trade for a shorter manifold and cash... local pickup available too...if you have a stock rb25 mani let me know too.

95 KA24de with 80k miles and auto tranny

koukizilla — 2009-11-18T20:12:12-08:00

car ran fine then my alternator went out. Since then i decided i wanted to go with a different route and will sell the KA.

500 for the motor and 100 for the tranny

obo

Power FC/740cc/CP Pistons/Greddy/DEFI/etc

greenman100 — 2009-11-21T11:20:50-08:00

Aftermarket SR parts:
Power FC D-Jetro (MAP version) with MAP sensor and commander - $850 shipped
CP Pistons 86.5mm 8.5:1 CR brand new, never used, in original packaging - $480 shipped
Greddy/Trust MLS headgasket 88mmx1.2mm, brand new in box. - $160 shipped
Tomei 740cc Fuel Injectors in rail - $330 shipped

Stock SR parts:
SR redtop MAF w/ pigtail: $40 shipped
SR coilpack harness - $20 shipped
SR spark plugs - $10 shipped
SR exhaust cam, no gear - $20 shipped.
SR OEM injectors in fuel rail - $75 shipped
SR Exhaust Manifold - $20 shipped
SR Turbo elbow w/ hardware- $20 shipped
SR Fuel Rail with 370cc injectors - $60 shipped
SR Ignitor - $55 shipped
SR redtop harness - $120 shipped

SR gaskets:
New 2-bolt gasket: $4 shipped
New 3-bolt gasket: $4 shipped
New 5-bolt gasket: $4 shipped
Used (reusuable) 4-bolt gasket: $3 shipped
Used (reusuable) 5-bolt gasket: $3 shipped

http://i32.tinypic.com/x4gnj8.jpg

DEFI gauges:
White Imperial Boost:
Comes with everything it came with new...gauge holder, link wire, sensor
$180 shipped.

White Imperial EGT:
Comes with gauge and sensor cable only - no sensor.
$80 shipped

Other:
Triple gauge A-pillar mount, 52mm. - $20 shipped.
Innovate LC-1 Wideband - mocked up, wiring is unused, comes with unwelded bung - $180 shipped

Pictures coming soon. Email is best: elmoret at ufl dot edu

Nissan Forums / Infiniti Forums - NICOclub: Engine / Drivetrain (for sale)

KA24DE For Sale

NY:WTB rb25 tranny

Ultimate SR20det swap -Built Motor!

RB20DET full swap into s13 for sale/part out

FS: Circuit Sports O2 Elimination Downpipe

VG30E + 5 Speed w/ stage 3 clutch

I need a 5speed kit for an S14

looking for

complete sr20det blacktop longblock part out!!!

FS - Tomei CA20 stroker kit

Anybody selling any kinds nos warmer kits

Z32/N62 MAF works perfect/w pigtail

NJ: KA24DE complete running engine for sale

APEXI AFC NEO AIR FUEL CONTROLLER UNIVERSAL

CT Fidanza flywheel and Centerforce clutch for ka24de

SC New Garrett GT2835R 700.00 Must sell

RB25DET TIMING Idler & Tensioner pulley and VALVE COVER Gasket - OEM BRAND NEW

z32 tt engine with around 20k from nissan rebuild

Drain plug gaskets (crush washers) NEW! OE nissan part

WTB: RB20DET Harness

FL: s13 catback exhaust 3"-3.5" No Ship

FL: s13 catback exhaust 3"-3.5" No Ship

Parts for sale, ka, sr make offers! Will ship!

NEW - sr20det Greddy RAS

s13 sr20det altenator

RB and SR STUFF TURBO's,ECU's AND MORE FORSALE CA SOCAL!!!!!!!!!

f/s brand new never used 740CC DW injectors. 280 shipped

KA24DE/T for sale and turbo kit

NJ: Kaaz 2 way diff

S14 SR20DET Turbo lines and S14 Sr20DET CATBACK EXHAUST

or: datsun 1600 su carbs and intake

$50 Shipped For a New BOV

Stillen high flow cats for 2007-2009 VQ35HR and VQ37VHR for sale.

Cluth pedal, 5speed Crossmem

FS: SR20det Intake Manifold

HUGE SALE: 90% Greddy Turbo Kit (KA24DE), Clutch, Aero

Fully Built Sleeved Mazworx 2.2L Sr20det block / exedy twin disk / peakboost

PA: KA24E stuff and 2 transmissions!! NO SHIPPING!!

s13 blacktop longblock parts for sale

NSW: D21 Performance parts INT. Postage available. Z24

NY/ FS:93-98 nissan 240sx power steering reservoir with lines uncut

FS:U13 Turbo manifold and J-pipe

Tons of oem parts... 240sx, sr20det, 350z

FS:Garrett T04S

Driveshaft shop axles rated for 650whp

KAAZ 1.5 way lsd complete pumkin

240 parts in nj take a look

Used 3.5 injectors 02 03 in rail Cheap!!

FS: Super Fresh HKS GT2540 & Garrett T25 Turbos

Fs-Brand new AEM Uego

FS-Brand New CP pistons

PA: driveshaft, rad, fuel (ca), ac. can ship

KA stuff: injectors, ecu, SOHC coil. (PA)

fs 2 2005 nissan titan motors

FS: [WA] Massive items FS, lots BNIB, great deals take a look!

KA24E Turbo kit

95 240sx clutch & brake pedals,master,booster,drive shaft.

NJ: Kaaz 2 way diff

s14/s13 parts

VA: SR20DET OEM MANIFOLD *MINT* LOOKS BRAND NEW!

rb20 stock turbo

F/S

FS : HKS SSQV BLOW OFF VALVE $130 OBO

MD: J30 LSD & Bumper OBO

Arias, Fidanza, Eagle, AMS

s14 zenki AC system

CA: SR T25 Fully Rebuilt and Balanced

FS: RB25 TUBULAR MANIFOLD

95 KA24de with 80k miles and auto tranny

Power FC/740cc/CP Pistons/Greddy/DEFI/etc

VA: SR20DET OEM MANIFOLD MINT LOOKS BRAND NEW!