engine damage. advice and suggestions needed please.

[suby01]

ya its going to be full warranty just matching up to what i had the 6 years 70k i think it is. i dont get a brand brand new one. i just get the warranty back technically lol. F that id let them keep the warranty for so much money.

[Poyzinous]

As far as i know, Infiniti dealers get paid dollar for dollar on warranty work. If it would cost 500 bux to the customer then the Infiniti (Corp) pays that to the dealer.That is why they love warranty work because they get the same money and the customer is happy because they don't have to pay!

And perry, thats not actually true. The dealer doesn't get dollar for dollar. Not service, not the techs, not parts dept. Rates are dropped, and percentage chunks are lower, so the tech and service rep only get between 70% and 80% as much if it were not warranty. Also, pricing for parts is set at a certain number infiniti decides, and so the Parts dept only gets about 70% of what they could be getting.

[pfarmer]

And perry, thats not actually true. The dealer doesn't get dollar for dollar. Not service, not the techs, not parts dept. Rates are dropped, and percentage chunks are lower, so the tech and service rep only get between 70% and 80% as much if it were not warranty. Also, pricing for parts is set at a certain number infiniti decides, and so the Parts dept only gets about 70% of what they could be getting.

You sure this should not be 'And Tampa'?

I figure they will make more money off warranty then on. However since warranty work is more of a 'stream' they like warranty work since it takes up some of the down time of the shop, a filler. I think warranty work is more of a break even and non-warranty work is at the higher margins. However without warranty work then during down times the shop has a negative cash flow. Even if warranty work didn't break even it decreases the amount of negative cash flow.

So if I understand the second part then there is a 30% markup on price. To me this 13k engine then is bringing in about 3500 bucks extra to the dealer with it 'off warranty'. So they get to charge the full amount for the engine making the profit on it (rightfully so) and do the same for labor for the install.

This would be a good reason to get the engine back for a cause of event analyses.

I don't believe in defrauding a corporation for warranty work which should not have been covered due to operation outside of the warranty. On the other hand if the product just may have had a defect to start with that could have affected the stock product then an adjustment may be in order.



Perry

[C-Kwik]

I figure they will make more money off warranty then on. However since warranty work is more of a 'stream' they like warranty work since it takes up some of the down time of the shop, a filler. I think warranty work is more of a break even and non-warranty work is at the higher margins. However without warranty work then during down times the shop has a negative cash flow. Even if warranty work didn't break even it decreases the amount of negative cash flow.

Work is work, even if they are getting paid a little less for it than regular work. But its work they didn't have to do any substantial marketing to receive. The other aspect is that it provides opportunity for cross-sales and can be a great opportunity to impress a customer to try and earn repeat business.

now with that said i was going to call the infiniti hq. but then when i talked to the service manager he said infiniti gave approval for the warranty then just like someone said they engine would need to be sent back and they will have it fully inspected and right then and there they will find the same fault as in the aftermarket part making the damage and will not cover it and charge the dealer back for it. and since they dont have mr bob tech working on it they had to call over some specialist so they do it right that person mite and will lose their job because of credentials. bla bla.

Its your money and thus your choice, but it simply pains me to see such a passive position when your talking about $13K. So I apologize if I come off persistent but I'd rather I see a member not have to drop that kind of coin without good reason.

That said, if a dealership makes a poor assessment then it is on them. As I said before, they can't charge you for what they do not get authorization for in advance. So their argument that Infiniti will send it back is weak. If this is what they contend, then the dealer can put that in writing. If not, then they should be asking Infiniti to make the call. As far as I can tell, Infiniti did not make the call here in any way, shape or form. Frankly, I'd be calling Infiniti to have them make the decision or at least confirm they were involved in the process. Last person I want making a decision on such a matter is one who serves to gain financially and is not bound to you under any kind of contractual obligation. From your description throughout, there is nothing transparent about what they are doing.

[Pamywyner]

Just wanted to let you know I believe I saw your car today! It was apart and my husband was told that it was the pullys that caused major engine damage. Guess they were waiting to hear back from the rep.

It was pretty crazy seeing it all apart like that. We've heard so many good things about these cars that it caught his eye and he had to ask about it. I told him I had been reading this thread on line for awhile now and had to be the same car!!

We wish you good luck with it. Sad to see it on the lift like that...

[SteveTheTech]

When you get into taking the engines apart on these cars for any significant reason they look like a mess. The last engine I did was in an FX45 I had parts and components and fluids everywhere. It's organized chaos. The majority of us can tell where 95% or the bolts go on these cars. Deep engine disassembly is impressive to see, the amount of stuff that is between the oil cap and the front of the engine is actually surprising.

[Pamywyner]

When you get into taking the engines apart on these cars for any significant reason they look like a mess. The last engine I did was in an FX45 I had parts and components and fluids everywhere. It's organized chaos. The majority of us can tell where 95% or the bolts go on these cars. Deep engine disassembly is impressive to see, the amount of stuff that is between the oil cap and the front of the engine is actually surprising.

Yes, my husband has been a tech and is a service manager with Goodyear for 28 years now. I'm surprised that he can put 'all that stuff' back together when an engine is apart!!! - but he can't figure out how to run a washing machine??

[SteveTheTech]

Yes, my husband has been a tech and is a service manager with Goodyear for 28 years now. I'm surprised that he can put 'all that stuff' back together when an engine is apart!!! - but he can't figure out how to run a washing machine??

My wife says the same thing. Something about that type of rational thought eludes us. My common area of .... failure include the back yard and completing the circle of laundry.

to Goodyear, I learned more in the 5 years I spent working in corporate stores in MA and VA than the next 5 years.

[C-Kwik]

When you get into taking the engines apart on these cars for any significant reason they look like a mess. The last engine I did was in an FX45 I had parts and components and fluids everywhere. It's organized chaos. The majority of us can tell where 95% or the bolts go on these cars. Deep engine disassembly is impressive to see, the amount of stuff that is between the oil cap and the front of the engine is actually surprising.

Its actually interesting to see how one can progress. My first major work was replacing a clutch on my 83 Celica. I must have read the Hayne's Manual 100 times as I worked up the nerve for it. It took me a weekend to complete but it was done. But I had about 8 bolts that I had no idea where they were supposed to go. As I began working on cars more and more, I ended up with less and less leftover parts. But until I stopped having parts leftover the running theme my friends and I shared was "if no parts are leftover, it wasn't done right."

but he can't figure out how to run a washing machine??

Have it modified so that the door opens with a hood latch, clothes are loaded through a funnel and the button to start it is a key.

[SteveTheTech]

My first major work was replacing a clutch on my 83 Celica. I must have read the Hayne's Manual 100 times as I worked up the nerve for it.

I never attempted a clutch in the driveway. I don't envy that, although the 84 was rwd wasn't it? The most crucial step in any type of major repair is making a mental note of the color,size, and location of everything you remove. A trick I learned along the way was to get a box of small ziptop sandwich bags and put the small components and bolts in bags, if the car is not going back together right away labeling them in conjunction with the picture from the FSM makes the reinstall much easier and almost eliminates the extra bolt pile.

Now I use an oil filter box and a magnetic tray (for large parts) when doing jobs of that scale. Space is at a premium though so things need to be in piles, as the cleanup guys tend to try to "help" and there is always more than one thing that needs your attention.

[C-Kwik]

I never attempted a clutch in the driveway.

I've done at least 7 in my driveway.

I don't envy that, although the 84 was rwd wasn't it?

Celicas were RWD up until 1986 IIRC.

The most crucial step in any type of major repair is making a mental note of the color,size, and location of everything you remove. A trick I learned along the way was to get a box of small ziptop sandwich bags and put the small components and bolts in bags, if the car is not going back together right away labeling them in conjunction with the picture from the FSM makes the reinstall much easier and almost eliminates the extra bolt pile.

Yeah, I did that when I replaced the headgasket and timing chain guides on my friend's 89 240sx. Its the first major repair I can recall that ended up with no missing or extra hardware.

[pfarmer]

I never attempted a clutch in the driveway. I don't envy that, although the 84 was rwd wasn't it? The most crucial step in any type of major repair is making a mental note of the color,size, and location of everything you remove. A trick I learned along the way was to get a box of small ziptop sandwich bags and put the small components and bolts in bags, if the car is not going back together right away labeling them in conjunction with the picture from the FSM makes the reinstall much easier and almost eliminates the extra bolt pile.

Now I use an oil filter box and a magnetic tray (for large parts) when doing jobs of that scale. Space is at a premium though so things need to be in piles, as the cleanup guys tend to try to "help" and there is always more than one thing that needs your attention.

I have done several clutches in the gravel, the hardest one being a 61 Sunbeam Alpine since you pull the engine and you pull it from under the car since access to the bell housing is so limited. The easiest being a 75 VW Scirroco, transmission on the kitchen table in under 45 minutes.

I always assume something will go wrong and keep all the parts organized. I once rebuilt my 650 Yamaha Engine in my living room, it took an extra month to get the parts so it ended up being a very good plan to keep everything all boxed and labeled. Basically a couple of square feet of engine took up the entire living room when disassembled. The one mistake I did make was the order of reinstallation of the oil pump which looked like it could go on at a certain time but you soon find out that you need to back up an hour or so in the sequence and start over. This is why it is also wise to have that lined up as well.

Perry

[SteveTheTech]

I envy you guys who tinker with cars as a hobby. I used to be like that, then I thought why not do what you like right??? I just cannot fathom doing heavy work on my back with the car <1meter off the ground, I'm a little spoiled an above ground rack is the best invention. Maybe I am a little jadded after a very long day.

I've done at least 7 in my driveway.

Yeah, I did that when I replaced the headgasket and timing chain guides on my friend's 89 240sx. Its the first major repair I can recall that ended up with no missing or extra hardware.

7 Really... or I don't know what is appropriate for that. You would be surprised how much different it is working on your feet.

I also cannot recall the last head gasket I have done...not usually a problem on 99.9% of Infinitis...and it usually works out cheaper in the unlikely event that something blows an HG to replace the whole engine with a low mile JY replacement. Although I am in a half as*ed hunt for a local RE4 rwd trans for rebuilding, but that is more of a project that will never come to fruition.

I have done several clutches in the gravel, the hardest one being a 61 Sunbeam Alpine since you pull the engine and you pull it from under the car since access to the bell housing is so limited. The easiest being a 75 VW Scirroco, transmission on the kitchen table in under 45 minutes.

...wow that doesn't really sound fun at all. VWs were notoriously easy to pull apart which made them a huge international success in the good old days. When I was with MB it was common practice to pull the engine for major repairs. I could pull an entire driveline out of an E and S class in about 1.5hrs. It always took about 2hrs-the whole day to get them back in(depending on work load). But that was in a body shop environment where it could be a month before you put the car back together and there was always one or more of your baggies missing.

It is kind of funny that warranty pays <2hrs to R&I a clutch on an older G.

[pfarmer]

...wow that doesn't really sound fun at all. VWs were notoriously easy to pull apart which made them a huge international success in the good old days. When I was with MB it was common practice to pull the engine for major repairs. I could pull an entire driveline out of an E and S class in about 1.5hrs. It always took about 2hrs-the whole day to get them back in(depending on work load). But that was in a body shop environment where it could be a month before you put the car back together and there was always one or more of your baggies missing.

It is kind of funny that warranty pays <2hrs to R&I a clutch on an older G.

In the case of the Sunbeam the transmission bolted to the bell housing on the inside of the bell housing with the tail shaft sitting inside of a cross memeber. The bell housing then was almost impossible to unbolt as well, so out the engine came to make it easy.

Perry

[SteveTheTech]

In the case of the Sunbeam the transmission bolted to the bell housing on the inside of the bell housing with the tail shaft sitting inside of a cross memeber. The bell housing then was almost impossible to unbolt as well, so out the engine came to make it easy.

Perry

I'm trying to visualize that and I think I need to go to the Google. Whatever it is it sounds awful. Very reminiccant of GM and the hatred for technicians when locating things like oil filters and other items that require periodic replacement.

[pfarmer]

I'm trying to visualize that and I think I need to go to the Google. Whatever it is it sounds awful. Very reminiccant of GM and the hatred for technicians when locating things like oil filters and other items that require periodic replacement.

Consider aligning the pilot shaft!

Perry
Modified by pfarmer at 10:45 AM 7/4/2009

[C-Kwik]

I envy you guys who tinker with cars as a hobby. I used to be like that, then I thought why not do what you like right??? I just cannot fathom doing heavy work on my back with the car <1meter off the ground, I'm a little spoiled an above ground rack is the best invention. Maybe I am a little jadded after a very long day.

I'm often glad I never went into work as a mechanic. I was urged to by a few people I knew, but I'm not sure I'd enjoy cars as much if I did. I hate working on stuff that isn't mine now.

7 Really... or I don't know what is appropriate for that. You would be surprised how much different it is working on your feet.

No worries man. I feel the same way sometimes. I'm proud of it at times, but when I'm in the middle of it, I always say, why the hell did I agree to this crap? Of course, half of them were my own so it was to save me some money. I can imagine working on your feet and with a proper transmission jack would make all the difference. Trying to get the upper bolts from under the car can be a real pain when you have to lift yourself up to it.

...wow that doesn't really sound fun at all. VWs were notoriously easy to pull apart which made them a huge international success in the good old days. When I was with MB it was common practice to pull the engine for major repairs. I could pull an entire driveline out of an E and S class in about 1.5hrs. It always took about 2hrs-the whole day to get them back in(depending on work load). But that was in a body shop environment where it could be a month before you put the car back together and there was always one or more of your baggies missing.

Frankly, with the headgasket and when we rebuilt my friend's motor, it would have been much better to pull the motor. With the headgasket, I didn't know better and was too late by the time I figured it out. With my friend's motor, we rebuilt his Supra motor with the block still installed. My friend insisted we not pull the motor despite my efforts to change his mind. The only good thing about that was we didn't have to truck around a motor to get it bored out (we did the work as he blew a piston, but he bought slightly oversized replacements). The local dealer referred him to a guy that had a mobile boring machine and did it in the garage. Expensive (relative to taking it in), but worked out fine.

[fiveliterbeater]

suby let me get this straight, you're going to have them put your car back 2gether for 13k????? this is crazy!!!! these guys are giving you the wrong advice!!! you need to tell those f*** at the dealer to keep their POS and do a voluntary repo on the car. ur credit will take a slight hit, but nothing that can't be fixed. on top of that you can take the money and get a newer better G37 sedan/coupe. forgive me if I mis-understood what ur decision is but I think ur crazy having those a-holes push you around! you are in control not them!

[Pamywyner]

I was at the dealer today and saw that suby01's car was put back together and gone. The old engine sitting outside.

Suby, give us an update!

[pfarmer]

...wow that doesn't really sound fun at all. VWs were notoriously easy to pull apart which made them a huge international success in the good old days. When I was with MB it was common practice to pull the engine for major repairs. I could pull an entire driveline out of an E and S class in about 1.5hrs. It always took about 2hrs-the whole day to get them back in(depending on work load). But that was in a body shop environment where it could be a month before you put the car back together and there was always one or more of your baggies missing.

It is kind of funny that warranty pays <2hrs to R&I a clutch on an older G.

I had the engine on the ground in a Corvair in under 50 feet. Wait a second that wasn't intentional. I was taking a fellow workers car out for a test drive. She wanted something like 50 bucks for it and I figured if it lasted a month it would be good enough for the 50 bucks. It lasted 50 feet when the engine fell on the ground and the car came to a halt. She comes screaming out of her booth 'what did you do to my car?'. Turns out it was missing the cotter key on the castle nut that holds the rear of the engine in place. It tore the ignition wires to the coil. I put the nut back on, put in a decent cotter key, spliced the wires, and she was able to drive off in about 20 minutes.

Think what this would have been like on I5 at 60 mph since that is where she drove everyday. She told me later she felt lucky that it failed when it did as it may well have killed her otherwise. Driving one of these was like driving a go kart. Driving a Monza was like driving a fast go kart.

Perry

[suby01]

Just wanted to let you know I believe I saw your car today! It was apart and my husband was told that it was the pullys that caused major engine damage. Guess they were waiting to hear back from the rep.

It was pretty crazy seeing it all apart like that. We've heard so many good things about these cars that it caught his eye and he had to ask about it. I told him I had been reading this thread on line for awhile now and had to be the same car!!

We wish you good luck with it. Sad to see it on the lift like that...

yes. correct it was mine!!

here are some pics of the operation. WARNING not a pretty sight.









but heres the update everyone. three weeks and $13,000 later. got it back. like new. thats got it back this sat. the reason why i wasnt on here before because i was #$%@% and then when i got it back i wasnt on here cuz i was out and enjoying my car back.

they seemed to put everything back together correctly. engines new squeeky clean. 150miles on it since sat, just sucks im back at the break in period meaning i actually have to drive it slow. wtf. if you know me you can feel for me how hard thats to do.

suby let me get this straight, you're going to have them put your car back 2gether for 13k????? this is crazy!!!! these guys are giving you the wrong advice!!! you need to tell those f*** at the dealer to keep their POS and do a voluntary repo on the car. ur credit will take a slight hit, but nothing that can't be fixed. on top of that you can take the money and get a newer better G37 sedan/coupe. forgive me if I mis-understood what ur decision is but I think ur crazy having those a-holes push you around! you are in control not them!

no it was $ 4800 to put it back together and restocking fee for the engine. just to get my car in the same way that i towed it in. i got my lawyer and tried to fight that but there was nothing that could of been done believe me i didnt like spending 13000 dollars as much as you thinking about me doing it.

if it wasnt for them charging me for the reassembly i would of towed the car down to cali and had a TT setup put in for a couple $$ more. but so be it it is what it is. that was just like heyy heres 5k for nothing just so u can give me my car back.

as far as performance mods for me now left is the intake high flow cats and catback exhaust. along with the full suspension and brakes. they said that if i leave it like that they shouldnt see any type of warranty problem in the future.

oh and a LOL note. when i went to the cashier to check out. it was like 5465403540 papers of paperwork w.e i hand it to the lady and then hand my credit card to her and im like 12000 on the card and the rest cash. shes just laughs OOH OOK. and takes the papers and trying to look for the total. im like heres my card can you swipe it? shes like so how much on the card?12000!ok really?i just told you look at the receipt.shes like OMG really you werent kidding me im so sorry what happened is everything ok?yes great fine i see my car shiny parked outside and im standing here talking to you :ank and not out so can you swipe this !@#$ thing and i can be so she did signed it over and i was out. shes felt kinda dumb i have no idea what went through her head but i was like its ok your still cool and have a wonderful weekend she smiled and handed me the keys.

any other questions?? other than that thanks everyone for being with me through this.

[pfarmer]

no it was $ 4800 to put it back together and restocking fee for the engine. just to get my car in the same way that i towed it in. i got my lawyer and tried to fight that but there was nothing that could of been done believe me i didnt like spending 13000 dollars as much as you thinking about me doing it.

as far as performance mods for me now left is the intake high flow cats and catback exhaust. along with the full suspension and brakes. they said that if i leave it like that they shouldnt see any type of warranty problem in the future.

any other questions?? other than that thanks everyone for being with me through this.

Did you get the engine or at least the crankshaft back. If I spent this type of bucks I would at least want the crank looked at to decipher exactly what killed the goose.

Perry